Filter Results By:
Products
Applications
Manufacturers
-
product
NTS Platform
Manufacturers all over the world are leveraging our NTS platform for products with rotating or otherwise moving parts, or produce sounds. Typical applications include mass production of air conditioning units, pumps or small electric motors, where errors in assembly can cause malfunctions or significantly shorten service life. This test platform is customized to your specification and application. Feasibility studies are available to ensure your solution is exactly what you are looking for.
-
product
High Speed Test Bench
AT444
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
product
Motor Test for Stepping Motors
*Stable measurement: Since it uses Prony braking, this model provides stable measurement unaffected by moments of inertia and no coupling loss. In addition, the resulting measurements allow data correlation via the traditional double-balance method.*Precision measurement method: This model’s judgment of synchronization loss achieves high stability using algorithms developed by Sugawara Laboratories. Measurement mode can be chosen based on step angle. For pull-in torque, startup can be measured consistently from the holding state. Allows measurement at 1-Hz resolution.*Broad measurement range: This model offers a range of seven available measurement heads, from 0.5 N to 50 N, allowing use for high-precision measurements. Through selection and use of pulleys, this model can also be used to measure small motors of 0.5 mN·m or less or 500 mN·m motors. Pulley diameters and other settings are easily configured using a personal computer running Windows®. Note: Any of the seven available heads may be attached to a single measurement component.*High-visibility measurement data: Motor characteristics are easily ascertained on automatically plotted performance graphs. Measurement data can be overlaid up to four times. In addition, the cursor can be used to read accurate values from measurement points. Hard copies of data displayed on-screen can be printed from a personal computer.*Can be controlled using standard personal computers: Allows control of measurement operations and display and storage of data from a standard personal computer running Windows®. Data is stored in CSV-format files for compatibility with other software applications.
-
product
Motor Test Instruments
The absorbed energy of the DCE series Dyno is converted into heat in two rotors located at the external side of the coils . The rotors are designed with curvilinear cooling fins for fast dissipating heat into the atmosphere . This design provides with the smallest physical size for air cooled Eddy-Current Dyno . Simple construction and desirable speed-torque characteristics are adaptable to most of the applications.
-
product
Motor Test Port
MTAP2
We know safety is number one priority in any motor reliability program that is why PdMA developed the MTAP2, our answer to safe electric motor testing. With the combination of MCEMAX® or EMAX, the MTAP2 makes testing easier, faster and above all safe!
-
product
Motor Test Bench For No Load Test
The testing equipment is extensively used in industries for testing of motors under no load conditions.
-
product
Custom Motor Test Systems
Magtrol's Customized Motor Test Systems (CMTS) are PC-based, turnkey systems custom designed and built to meet your specific motor testing requirements. By integrating Magtrol's motor test equipment with power supplies, adaptable fixtures, custom tables/cabinets, printers, etc., Magtrol's engineering team can customize PC-based, turnkey systems and modular test benches for almost any motor test application.
-
product
Electric Motor Test Systems
Electric Motor Test Systems feature our highly successful water brake dynamometer which is used as an electric motor loading device.
-
product
Motor Drive Test Systems
Drive and motor systems present unique challenges for test systems and Intepro combines regenerative active electronic loads to reduce the energy needed to do the tests as well as sophisticate instruments and supply voltages to test these demanding applications and provide meaningful results for the electrical and mechanical power parameters.
-
product
Motor Stator Test System
Chroma 1920
Chroma Systems Solutions, Inc.
For electrical safety and quality testing functions of motor stator coils
-
product
Motor Test for Electric Scooters
*The performance data of electric motors, in the majority of all cases, is performed by a brake test. Power input is calculated from current and voltage. Torque and power output are measured with a brake. It is important to reach, for each point, a persistent temperature. In case of large outer rotor BLDC motors, which are usually used for electric scooters, this traditional procedure may take many hours to complete, and is very complicated. *For several years, an innovative motor tester of MEA Testing Systems Ltd. is on the market. This testing system avoids any temperature confusion by testing a motor at constant temperature over the entire speed range. The test procedure is very fast, and gives the full load performances, including PWM current, voltage, torque, and driver efficiency, from stall up to no load. *During the test procedure, the motor is freely accelerated from stall to no load speed. The load of the motor is only the predetermined inertia of the rotor. From the moment of inertia and the acceleration, the torque of the motor is calculated and, also, the power output over the whole speed is given. Since the entire measuring time, depending on the motor size, is usually less than one second, the motor has no time to warm up. It remains at room temperature.
-
product
Development Test Stands for Electric Motors
Development test stands from imc are characterized by high flexibility in electric motor trials. A comprehensive variety of motor types can be tested and a complete range of tests carried out. The mechanical configuration consists of a test bed with a load machine and a torque measuring shaft. The load machine and torque sensor shaft are mounted on a linear guide and precisely aligned axially by means of laser. It can be moved towards the test object on ball bearings, as a complete unit. Especially time-saving: no need to realign the load machine assembly when changing the torque sensor.
-
product
Development Test Stands for Electric Motors
Development test stands from imc are characterized by high flexibility in electric motor trials. A comprehensive variety of motor types can be tested and a complete range of tests carried out. The mechanical configuration consists of a test bed with a load machine and a torque measuring shaft. The load machine and torque sensor shaft are mounted on a linear guide and precisely aligned axially by means of laser. It can be moved towards the test object on ball bearings, as a complete unit. Especially time-saving: no need to realign the load machine assembly when changing the torque sensor.
-
product
Motor Quality Control Test Systems
SKF Condition Monitoring Center
These rack-style motor quality control units are rugged, field-proven systems for testing stators and armatures in high-volume manufacturing environments. They combine the most common electrical tests into an efficient automated solution.
-
product
Production Test Stands for Electric Motors
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
product
Test Sets For Motor & Generator Industries
Test Sets For Motor & Generator Industries are designed for no-load loss as well as heat run testing. They are ideal for offering clean power with precise regulation as well as voltage control. These sets are designed when there is no need of frequency conversion. With variable-frequency drive of these sets, they are used to select any output frequency from 50 Hz to 60 Hz. in addition to this, for larger requirements, from 50-to-200 Hz, this has been used as one of the most economical testing sets.
-
product
Test Setup For Domestic Mixer Motor
SCR ELEKTRONIKS have developed TESTING SET UP FOR MIXER MOTOR for carrying out performance test and High Voltage test of mixer at final stage. It consists of Voltmeter, Ammeter and Watt meter for observing the values of different parameters. OK / NOT OK lamps are also provided to display the results of HV test. HV test is provided with tripping cut off concept. Output Socket is provided for quick connections and disconnections of the equipment to be tested. User friendly operations make the equipment to be handled easier for any operator.
-
product
Traction and Induction Motor Test Systems
Crest makes state-of-the art test systems for testing 3-phase AC motors used in traction and other industrial applications.
-
product
Development Test for Electric Motors with Power Electronics
Test bench for electric machines and inverters in hybrid applications*Control of mechanical parameters*Verification of electrical properties*Checking the LL characteristics*Short circuit measurement*Recording the performance process*Noise measurement*Temperature measurement
-
product
Motor Tester
Changzhou Chanlon Electronic Technology Co., Ltd.
This machine is applied to test steel casing motor such as pump, fan, air-condition motor, mower, paper shredder and refrigerator etc. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stator.
-
product
Motor Testing
Electronic Systems of Wisconsin, Inc.
ESW's Motor Test Systems come fully equipped with the latest industry features based on your testing needs. The on-screen display in our testers make it easy to read, track, and record your motor information during the testing process. We realize this importance and want to make sure you never have to worry about losing key information ever again. Performance and reliability are important, so we make sure you will have full confidence of every motor you test, whether you place it in your product or send out the door to your customer. ESW's design team works closely with you to determine the tests you need, in order to make a system that will meet all your testing needs. See the slideshow below to see some of our Motor Testers.
-
product
AC Motor Tester
JK115
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical performance test of single-speed, multiple-speed single-phase induction motors.
-
product
AC Motor Tester
AIP892X series
Qingdao AIP Intelligent Instruments Co., Ltd
This product is suitable for electrical performance testing of all types of motors, such as home appliance motors (washing machines, air conditioners, fans, etc.), pump motors, stepper motors, etc. One-stop testing completes all set items, stable, fast, efficient and accurate, widely used by domestic and foreign enterprises.This AC motor tester test items: AC Hi-pot, insulation resistance, surge, DC winding resistance, no-load characteristics, low voltage start, locked rotor, rotation, PG characteristics.
-
product
Hall Motor Tester
Shanghai Aoboor Electric Co., Ltd.
Applicable to no-load test and any DC motor with internal hall elements.
-
product
HDD Motor Testers
BK8015/BK8015A
The BK8015 HDD Mechanical Specifications Tester and the BK8015A HDD Circuit Specifications Tester were designed and manufactured by BaKo to test HDD motors as they come off the assembly line. The two machines are complementary, and were designed to test a complete set of HDD motor characteristics.
-
product
Motor Armature Tester
DS720
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical properties test of motor armature with any number of communator bars, for example, automotive motors, motorcycle starter motors, Power tools motors, traction motors, vacuum cleaner motors, fitness equipment motors.
-
product
Motor Armature Tester
DS920
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical properties test of motor armature with any number of commutator bars, for example, automotive motors, motorcycle starter motors ect.
-
product
Motor Driven Actuator
NJ-SERVO Series
The NJ-SERVO electric motor driven actuator utilizes an electric motor drive system. High accuracy test control is enabled by a special servo motor and stroke displacement measurement sensor. In addition, the system configuration is simpler in comparison to hydraulic actuators, so it is easy to maintain, and achieves power savings and space savings. This system accommodates a wide range of tests with a high degree of expandability. This includes everything from endurance evaluations of the main body and assemblies of automobiles, aircrafts, and other transportation equipment to endurance evaluations of stand-alone parts; from multi-axis tests combining multiple actuators to uniaxial tests; and from sine waves to working waveform simulation tests.
-
product
Motor Octane Testing
DewTrak II MO
DewTrakII MO dew point/humidity transmitter is an optical chill mirror hygrometer designed to continuously measure the moisture content and Barometric pressure in the motor octane testing process. It is used to monitor and ensure compliance with test
-
product
Motor Performance Tester
CT Series
Shanghai Aoboor Electric Co., Ltd.
Test the cogging torque of motors, separate motor cogging torque and friction torque accurately; cogging torque test results is independent of test speed and speed fluctuation.
