Filter Results By:
Products
Applications
Manufacturers
- InterWorking Labs, Inc.
product
Network Emulator and Protocol Tester
Maxwell Pro
The Maxwell Pro Network Emulator helps engineers learn how their products will perform in mobile, cloud, and WAN networks. By capturing and changing network flows, Maxwell Pro can induce the conditions that cause network congestion, slow links, time outs, Lossy networks (LLNs), and many other adverse network conditions. Engineers can then see the effects on the device or application to find and fix bugs, solve network problems, and learn the limits of device and application performance.
-
product
4-in-1 OSLT Calibration Kit, DC to 26.5 GHz, Type-3.5 mm (f) 50 Ohm
CK521A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Fault Locator
BIDOYNG
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
product
40 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3710
The aTCA-3710 is a high performance, high bandwidth, 40G Fabric switch blade for AdvancedTCA® platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controller, DPI/security network, IPTV, IP multimedia subsystem, RNC/BSC, broadband access/bearer network, data center, and LTE/4G network applications. The aTCA-3710 provides 40GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
product
Coaxial Calibration Kits
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Rosenberger offers the following types of calibration kits with a range of coaxial connector series for vector network analyzers (VNAs). All Rosenberger calibration kits can be used from DC to their maximum frequency. Full version with adaptors and sliding loads for variable measurements Industrial version for standard measurements LRL and TRL version
-
product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (f)
CK058F
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
3-slot Network Attached File Server
DTS3
Curtiss-Wright Defense Solutions
The Data Transport System 3-slot (DTS3) is a rugged Network Attached Storage (NAS) file server for use in mobile vehicles, field ground stations, and aircraft. The DTS3 is easily integrated into network centric systems providing an easy-to-use, turn-key, rugged Network File Server (NFS). The system houses three Removable Memory Cartridges (RMC) that provide quick off load of data.
-
product
Voltage Probe
KHZ43201
Beijing KeHuan Century EMC Technology Co,.LTD
The KHZ43201 voltage probe is a standard low resistance test probe, which meets the technical requirements for this product in the CISPR16-1 and CISPR14-1 test equipment. When measuring the interference voltage of the power grid, the artificial power supply network cannot be used at the load port, and sometimes it is necessary to use a voltage probe to measure the interference of the signal port, the load port, and the antenna port. The input impedance of the voltage probe to the ground wire is greater than 1.5KΩ, which can protect the input terminal of the receiver.
-
product
Dual-channel AMR Modem
Signals & Systems India Private Limited
DUAL-CHANNEL AMR is a combined Modem for remote reading & local reading via Bluetooth through the mobile app without opening the enclosure/seals. Dual Channel AMR Modem is an innovative device that can be connected to any make of electronic energy meter by means of optical/ RS232 port, which is compliant to DLMS – IEC 62056-21 standard. AMR system is compatible with 4G network to push the power consumption-billing data, load survey data, and event data to a cloud-based server, with fallback to 3G & 2G. The modem can be programmed to send any abnormal events to any number instantly. The modems have a ‘store and forward’ facility.
-
product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (m)
CK058M
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Amplifier, Switch and Test Box
CLIOQC Model V
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
product
Web Application / Services Testing Tool
JMeter™
The Apache Software Foundation
Apache JMeter may be used to test performance both on static and dynamic resources (Webservices (SOAP/REST), Web dynamic languages - PHP, Java, ASP.NET, Files, etc. -, Java Objects, Data Bases and Queries, FTP Servers and more). It can be used to simulate a heavy load on a server, group of servers, network or object to test its strength or to analyze overall performance under different load types. You can use it to make a graphical analysis of performance or to test your server/script/object behavior under heavy concurrent load.
-
product
4-in-1 OSLT Calibration Kit, DC to 18 GHz, Type-N (f) 50 Ohm
CK519A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Automatic Calibration Module
ACM4509
ACM4509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full four-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to 18 connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
product
ARINC 664 Simulator & Analyzer Applications Software
F-SIM-A664
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 664 Interfaces - Simulate Multiple ARINC 664 End Systems Simultaneously - Full definition of input/output VLs, input/output Sampling and Queuing message ports, & TFTP Clients & Servers - Capture & Analyze Data from Multiple Virtual Links (VLs) - Live display showing all of the detected ARINC 664 VLs and message counts - Live displays showing all of the detected source and destination message (UDP) ports - Record network data to PCAPNG for use with Wireshark - Replay Previously Captured Bus Data - Also Supports MIL-STD-1553, ARINC 429 & Data Load operations
-
product
Test Solution
Novus, Novus-M, & Novus-R 100/25GE Load Modules
Keysight Network Applications and Security
Novus, Novus-M, and Novus-R are Ixia’s next-generation architecture and test solutions that satisfy the test needs of both high-density, multi-rate switch/router makers and the organizations implementing the network equipment. Supporting eight native QSFP28 100GE ports and up to 32-ports for 25GE per load module, Novus load modules enable interoperability and functional testing, as well as high-port count performance testing.
-
product
Purpose Built Network Packet Brokers
Garland Technology’s Purpose Built Network Packet Brokers (NPBs) are devices that provide access to network traffic from multiple links, helping to centralize and improve efficiencies by sharing packets between the monitoring and security appliances. Additional NPB features include filtering, aggregating, regenerating, and load balancing.
-
product
Ethernet Testing Network Performance
Networked Communication Solutions, LLC
Xena Networks and Veryx Technologies have created an innovative Ethernet test platform that combines Xena’s high performance, wire-speed Ethernet test hardware with Veryx’s broad portfolio of IP & Ethernet functional and conformance test suites. The result: an affordable, high-performance platform for IP & Ethernet load stress, protocol conformance & functional verification testing.
-
product
Cable & Antenna Analyzer
CAA-100
ShinewayTech® CAA-100 cable & antenna analyzer can test Return Loss and VSWR of load’ frequency. Also can get Return Loss, VSWR of DTF (distance-to-fault) and Cable Loss. Users can be easy to know the connection of cable & antenna system is reliable whether or not. CAA-100 series with frequency range 25MHz-4GHz and 60dB dynamic range can suitable for 2G/3G/4G/WiMAX system etc. CAA-100 series is the necessary measuring instrument for the new generation of wireless network development, upgrade and maintenance.
-
product
Performance Testing
We do performance testing of applications across domains and technologies, including web-based n-tier applications, client-server applications, SOA based solutions or COTS solutions. We have experience with all industry-leading performance testing and monitoring tools, along with expertise in end-to-end application performance including network, database, hardware, etc. We publish a detailed performance testing report for the application with response times, break-point, peak load, memory leaks, resource utilization, uptime, etc. We provide clear and actionable application tuning recommendations and help you implement those working closely with various IT teams in your enterprise.
-
product
Multi-Layer Analysis for Next Generation PONs
Multi-ONU Emulator
The NG-PON Xpert multi-layer analyzer is a unique, real-time protocol analyzer for XG-PON1, NG-PON2 and XGS-PON networks and products. The Multi-ONU Emulator introduces a new revolutionary approach for comprehensive testing of an OLT. It enhances the testing with repeatable test scenarios and functionalities that cannot be tested in any other way, including the OLT's ability to handle various ONU models and configurations, error and defect conditions, alarms and traffic loads.
-
product
RS-232/RS-485 Converter
ECD485
Deploy sub-metering sites and simple metering networks with ease using the EDMI MiniHub RS-232 to RS-485 converter.1/4 Load RS-485 modules allow for up to 128 devices over 1.2km of wired daisy-chain network, with each meter capable of becoming the Network Master and remotely connecting to a backhaul system via an integrated EDMI Modem Port redirect connector.
-
product
Ethernet Gateway for Woodward Easygen Genset Controls and LS-5 And DTSC-200 Controls
ESENET
ESENET is an Ethernet gateway specifically designed to interfaceWoodward's Easygen series genset controls with Modbus/TCP networks. It interfaces via the load sharing CAN bus with the Woodward controls.
-
product
Network Analyzer
DPNA-6G AXIe
The AXI DPNA-6G module is the world's first network analyzer in the form factor of the AXIe-1 module, as well as the first Russian device that meets the AXIe-1 standard. In the mode of the network parameters meter, the AXI DPNA-6G module measures the vector values of the network parameters on two ports: transmission coefficients (S12, S21) and reflection (S11, S22). At the same time, all necessary types of calibrations are supported: one- and two-port short-circuit, XX, matched load, transmission normalization. The software supports the import of third party calibration standard parameters. In the measuring receiver mode, the module provides:*generation of a harmonic signal (frequency synthesizer);*spectrum analyzer and power level in a given band;*measuring the frequency of a known signal;*measurement of analog modulation parameters;*phase noise measurement.
-
product
2-Port 20 GHz Analyzer, Direct Receiver Access
C2220
C2220 Vector Network Analyzer delivers industry-leading dynamic range and sweep speed, with all the features engineers have come to expect included standard in our software. The C2220 network analyzer has direct receiver access for special applications involving external directional coupling, including Load Pull and high power measurements.
-
product
Load Management
We help DSOs monitor and understand complex power flows through today’s distribution networks, optimize load management strategies and prepare for tomorrow’s challenges
-
product
Software
SSI-TRES
Was developed to read and edit Plug and Play Smart Sensors that are compliant to the IEEE 1451.4 Standard. TEDS, or transducer Electronic Data Sheet, is a set of electronic data in a standardized format defined within the IEEE 1451.4 standard. This data specifies what type of sensor is present, describes its interface, and gives technical information such as sensitivity, bridge type , excitation, etc. This information is stored in an EEPROM chip attached to the sensor. By having this chip, the sensor can identify and describe itself to the network and or Smart Load Cell Meter (DPM-3), thereby easing automatic system configuration.
-
product
1 Mm Calibration Kit
85059B
The Keysight 85059B is a 1.0 mm calibration kit designed for vector network analyzer systems operating over the frequency range of DC to 120 GHz. The opens, shorts and loads in this kit are optimized to provide accurate and traceable calibrations over the specified frequency range. The 85059B with 85059V 1 mm Verification kit are replacements for the 85059A 1 mm calibration/verification kit.
-
product
Economy Mechanical Calibration Kit, DC To 3 GHz, Type-F, 75 Ohm
85039B
The Keysight 85039B calibration kit, with option M0F, contains male and female type-F open, short, and load standards. This calibration kit works with all 75 ohm network analyzers and test sets for measurement of devices with 75 ohm type-F connectors. The kit also includes type-N to type-F adapters. More economical versions of this kit are available by ordering option 00F for the female standards only, or option 00M for the male standards only. This kit is specified from dc to 3 GHz.
-
product
Telemetry Handheld Display
TW-3.0-T
The TW-3.0-T Telemetry Handheld Display is a modern, slimline, multifunctional load monitoring device which is unique to DLM.This innovative design is built with the user in mind. It has a large, high quality LCD screen which is optically bonded removing the need for a back light and improving clarity in bright sunlight. There are 12 devices on the network which can each be given a customisable friendly name made visible on the screen to make instant identification possible.
-
product
Enterprise-Scale Application and Security Testing
PerfectStorm ONE 1GE/10GE Appliance
Keysight Network Applications and Security
PerfectStorm ONE facilitates network and security proof-of-concepts (POCs) and assessments, all in a compact device. This POC-in-a-box enables enterprises and service providers to select optimal devices and right-size data centers, as well as providing device vendors with a platform to fully showcase their product’s performance, resiliency, and throughput under realworld traffic loads.
