Filter Results By:
Products
Applications
Manufacturers
-
product
Printed Circuit Board
RISER-PPM-1
WINSYSTEMS’ RISER-PPM-1 boards are designed to provide extra space in a PC/104-Plusstack. They are printed circuit boards (PCBs) with PCI-104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
product
Printed Circuit Board
RISER-PCM-1
WINSYSTEMS’ RISER-PCM-1 boards are designed to provide extra space in a PC/104 stack. They are printed circuit boards (PCBs) with PC/104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
product
PC/104 Single Board Computer with Vortex86DX3 System-on-Chip
CM1-86DX3
The CoreModule CM1-86DX3 is a PC/104 board with DMP Vortex86-DX3 single chip solution and has a very good performance to power ratio. The board comprises all peripherals needed for an embedded PC on a small 3.775" by 4.050" printed circuit board. The CM1-86DX3 integrates a powerful yet efficient DMP Vortex86DX3 with graphic controller and audio controller together with an additional GBit Ethernet controller to form a complete PC, with all the standard peripherals already onboard. Two Ethernet ports (1x GBit and 1x 100MBit), four RS232/RS422/RS485 serial ports, two USB 2.0 host controller to handle the communication with external devices. There are PS/2 connectors for keyboard and mouse. A first generation SATA interface allows the connection of hard disk or CD drive. CFast is also available. System expansion can easily be realized over the PC/104 bus connectors.
-
product
ISSRs for Mounting on Printed Circuit Boards
Series LS10
Series LS10 DC solid-state relays are designed for mounting on printed circuit boards. They facilitate heat-sinking by providing an interface surface. They can switch loads with high starting currents. The nominal switched currents depend on the size of the heat sink These relays use a direct-bonded copper substrate for thermal efficiency and long life.Available options include:LS60DC10C-21 10A, 7-36 Vdc Load; 3-10 Vdc ControlLS60DC10F-21 10A, 7-36 Vdc Load; 7-30 Vdc Control
-
product
Printed Circuit Board Inspection System
NIDEC-READ offers an array of testing equipment used to conduct open/leak tests on motherboards, as well as many other printed circuit boards. They can be flexibly configured according to applications in terms of size, type, and the number of test pins required.
-
product
Printed Circuit Board Testing Solutions
IES Systems is a turnkey test systems solution provider with 10 years of proven experience in printed circuit board testing solutions. Our experienced engineers design electro/mechanical solutions to interface between your product and our custom designed test instrumentation. We provide a complete solution to your PC board testing needs.
-
product
Printed Circuit Board Bending Test Jig
Evaluation of Bending Strength of Electronic Components and Substrates
-
product
Panel Mount With Fan Out For Connecting To A Printed Circuit Board
Panel Mount With Fan Out For Connecting To A Printed Circuit Board
-
product
Design, Manufacture & Test of Complex RF/Microwave Printed Circuit Boards (PCBs)
Teledyne Labtech specialises in the design, manufacture and test of complex RF/Microwave printed circuit boards (PCBs). - Technology driven – we innovate- Turnkey - one stop for manufacture, assembly & test- Focused – technical design support for RF/microwave and large format PCBs
-
product
Functional Testing of Printed Circuit Boards, Sub Assemblies and Finished Products
Testpoint
Yelo Testpoint is an extremely modular and flexible system, allowing you to scale to any size operation, and to add almost any new test requirements. Ideally suited to cellular manufacturing, the system can be used to complement an existing ATE, as a functional test add-on, or as a diagnostic work station. Its compact, space-saving construction has multiple interface positions to accommodate both horizontal and vertical connections.
-
product
Short Circuit Finders
The ShortSniffer locates short circuits in electronics circuits, projects, and printed circuit boards. * locates PCB shorts under solder mask, under components, and even on inner PCB layers * non-contact (inductive) pickup wand * pinpoint short to within 2mm radius (SS2) * rapid location with audio feedback * "follow the sound to the short" * no need for relative or reference measurements * battery operated * diode clamped current drive, won't harm your circuitry
-
product
Breakout Boards
"Breaks out" these pins onto a printed circuit board that has its own pins that are spaced perfectly for a solderless breadboard, giving you easy access to use the integrated circuit.
-
product
Noise Board
332D-11 VG
This printed circuit board was designed to original specifications and contains OEM specified parts. This board is required for testing the 332D-11 series gyros. Also contained on board is the Method A type calibration and sample and hold circuits required to perform the calibration of the noise circuits.
-
product
Monitor SDR Boards
Multiple Access Communications Ltd.
MAC Ltd’s MONITOR product family includes a number of software-configurable digital signal processing platforms intended for use in radio frequency (RF) receiver and transceiver applications. The MONITOR products are available in assembled printed circuit board (PCB) form for integration into larger systems. They also form the basis of MAC Ltd’s CatchAll™ radio products. In addition to the standard products listed below, MAC Ltd is happy to discuss the customisation of existing products and/or the development of new bespoke hardware and software.
-
product
Thermal Load Boards
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
product
Board Test Fixture Probes
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
product
Control Board For Testing PCBs
TCC 1800
The TCC1800 Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via a galvanically separated USB interface. The TCC1800 is designed to work with positive voltages up to 24V. All inputs and outputs are protected against higher voltages however. The card provides basic IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, Serial (UART) and I2C interfacing.
-
product
PCBA & Bare Board Cleanliness Tester
Zero-Ion G3
For two decades, thousands of electronics assemblers have relied on the Zero-Ion cleanliness testing to verify the cleanliness of post-reflow printed circuit assemblies and bare boards. Over time, as PCB assemblies have become more complex and more densely populated with surface mount components, and as vigorous quality standards such as ISO, TQM and Six Sigma have become commonplace, the ability to meet—and confirm—cleanliness levels has grown in importance. The Zero-Ion ROSE tester has kept pace with customer requirements, and the Zero-Ion G3 is the most advanced Zero-Ion ever designed, capable of testing assemblies reflowed with any solder paste, including no clean—yet its also one of the most affordable cleanliness testers on the market as well, with performance and ease of use second to none.
-
product
1.0/2.3 Connectors
Pasternack 1.0/2.3 connector category has many part numbers, most are RoHS and REACH compliant. 1.0/2.3 connector series in this category will terminate to coax or PCB (printed circuit board). Our 1.0-2.3 connectors are built to precise RF and microwave industry specifications. 1.0-2.3 connector series is manufactured in jack or plug gender with 50 Ohm impedance. 1.0-2.3 connectors are available in straight or right angle versions, as well as, bulkhead or mountless options. These 1.0 / 2.3 connector designs include crimp/solder, solder or solder/solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 1.0/2.3 connector series is in-stock. Not only are these 1.0-2.3 connectors in stock, but they ship the same day as they are purchased.
-
product
10-32 Connectors
Pasternack 10-32 connector category includes many part numbers, most of which are RoHS and REACH compliant. 10-32 connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack 10-32 connectors are built to precise microwave and RF industry specifications. 10/32 connector items are constructed in male or female gender with 50 Ohm impedance. Connectors in 10-32 series are available in straight or right angle versions, as well as, bulkhead or mountless options. These 10-32 connector designs include clamp/solder, crimp/solder or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 10-32 connector series is in-stock. Not only in stock, but will also ship the same day as purchased.
-
product
1149.1 Boundary Scan Feature, GTE 10.00p
K8212A
Boundary scan is a method for testing interconnections on printed circuit boards. Keysight’s Interconnect Plus Boundary Scan feature enables all the tools required to develop and execute this foundational test method on the board under test.
-
product
1149.1 Boundary Scan Feature, GTE 10.00p
K8212B
Boundary scan is a method for testing interconnections on printed circuit boards. Keysight’s Interconnect Plus Boundary Scan feature enables all the tools required to develop and execute this foundational test method on the board under test.
-
product
16 Channel, 12-Bit Analog Input PCI Card
PCI-AI12-16A
Model PCI-AI12-16 is a multifunction, high-speed, analog-to-digital converter board for use in PCI-Bus computers. It accepts up to 16 single-ended or eight differential inputs. The board uses a low-noise, multilayer printed circuit board. Inputs are protected against overvoltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts.
-
product
2.5-inch IDE Disk Adapter
4946
The HDD is positioned midway such that the PMC component envelope is not violated. Furthermore, steel rails are attached to the printed circuit board, allowing for a secure, robust installation of the hard disk drive. This is a superior mechanical approach, compared with other printed circuit board-based solutions available on the market.
-
product
2-Module ICT System, I317x Series 6
E9902G
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
product
4-Amp Solid-State Single Inline (SIP) Four-Pin Relays
Series BS
Series BS 4-amp solid-state single inline (SIP) four-pin relays are designed for mounting on a printed circuit board. BS relays can withstand very high current overloads. The compact size and triac output make the BS relay an excellent choice for switching medium power resistive loads. All Series BS relays are Zero-Cross switching.Available options include:BS24D4A 4Arms, 15-280Vrms, 600Vpeak Load; 3-10Vdc Control
-
product
75 Ohm 1.6/5.6 Connectors
Pasternack 75 Ohm 1.6/5.6 connector category includes many part numbers, the majority are RoHS and REACH compliant. 75 Ohm 1.6/5.6 connector series in this category will terminate to coax or PCB (printed circuit board). Our 75 Ohm 1.6-5.6 connectors are built to precise industry specifications. 75 Ohm 1.6-5.6 connectors are constructed in jack or plug gender with 75 Ohm impedance. 75 Ohm 1.6/5.6 connectors are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm 1.6-5.6 connector designs include clamp/solder, crimp/solder or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 75 Ohm 1.6/5.6 connector series is in-stock. Not only are these 1.6 / 5.6 connectors in stock, but they also will ship the same day as they are purchased.
-
product
75 Ohm BNC Connectors
Pasternack 75 Ohm BNC connector category contains many part numbers, most are RoHS and REACH compliant. 75 Ohm BNC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack 75 Ohm BNC connectors are built to precise RF and microwave industry specifications. 75 Ohm BNC connector are available in male or female gender with 75 Ohm impedance. BNC 75 Ohm connectors are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These 75 Ohm BNC connector designs include clamp/solder, compression, crimp/solder or solder attachment methods. We offer 75 Ohm BNC connector with standard or high performance levels constructed with brass or stainless steel bodies. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm BNC connector group is in-stock. In addition to being in stock, these BNC 75 Ohm connectors will ship the same day as they are purchased.
-
product
75 Ohm MCX Connectors
Pasternack 75 Ohm MCX connector category includes several part numbers, the majority are RoHS and REACH compliant. 75 Ohm MCX connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These 75 Ohm MCX connectors are built to precise RF and microwave industry specifications. MCX 75 Ohm connectors are available in jack or plug gender with 75 Ohm impedance. 75 Ohm MCX connector products are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm MCX connector designs include crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this MCX connector series for 75 Ohm is in-stock. Not only are they in stock, these MCX 75 Ohm connectors will ship the same day as purchased.
-
product
75 Ohm Mini SMB Connectors
75 Ohm Mini SMB connector category from Pasternack includes many part numbers, the majority are RoHS and REACH compliant. 75 Ohm Mini SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our 75 Ohm Mini SMB connectors are built to precise microwave and RF industry specifications. Pasternack 75 Ohm Mini SMB connectors are built in jack or plug gender with 75 Ohm impedance. Mini-SMB 75 Ohm connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel or mountless options. These 75 Ohm Mini SMB connector designs include crimp/solder or solder attachment methods. We offer 75 Ohm Mini-SMB connectors with standard or high performance levels manufactured with brass or stainless steel bodies. As with our other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm mini SMB connector series is in-stock. Not only are these mini-SMB 75 Ohm connectors in stock, they also ship the same day as they are purchased.
