Filter Results By:
Products
Applications
Manufacturers
RF Amplifiers
take low power RF signals and output RF signals that vary in the same way as the input signal, but with a raised amplitude.
See Also: Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers, Microwave Amplifiers, Rf Power Amplifiers
- Pickering Interfaces Inc.
product
PXI/PXIe RF Multiplexer, Quad 4-Channel, Terminated Common, 3GHz, 50Ω, SMB
42-876A-004
The 40-876A-004 (PXI) and 42-876A-004 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 4 banks in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
product
Wideband GaN Amplifiers
The Teledyne RF & Microwave family of GaN-based amplifiers maximizes power density and efficiency, and establishes a new benchmark for small size in the 0.1 to 6.0 GHz range that operates over multi octave. With dimensions of 2.5"L x 2"W x 0.42"H at only 2.1 cubic inches, these modular, non-ITAR GaN amplifiers maintain the rugged design characteristics needed for harsh airborne and land based requirements.
-
product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - 3U VPX
Model 54891
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex® UltraScale™ FPGA- Five GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Optional optical interface for data streaming- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
RF Amplifiers
AR RF/Microwave Instrumentation
Our “A” and “W” Series amplifiers have the power to deliver all the field strength you need. With unsurpassed mismatch capabilities and excellent flatness, they provide all the power promised over the entire operating band.
-
product
RF Amplifier
SA1001H
Hangzhou Softel Optic Co., Ltd.
*SA1001H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network.. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network*It is more convenient for debug engineering debug, because of the plug-in diplexer filters with built-in adjustable equalizers, adjustable attenuators, plug-in output splitters and scientific and reasonable ports for online test.*These equipments will work in the field rugged environment for a long time continuously, because of the aluminium alloy casing, good heat dispersing performances, beautiful looks, dependable linear power supply and lightning protection systems.
-
product
Power Sensors
RTP5540
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 40 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements. This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
product
VECTOR-GUN HANDHELD DIRECTION FINDING ANTENNA SYSTEM
HFDF
National RF's Type HFDF active directional antenna system consists of a high gain RF amplifier coupled to a tunable Faraday shielded loop antenna. Several loop antenna assemblies are available to provide coverage of frequencies in the HF and low VHF spectrum. Due to the nature of a Faraday shielded loop, the antenna exhibits a sharp null through the diametric center of the loop. This null is used to determine the direction of incoming radio signals or to locate electrical noise being radiated from some source. The internal high gain amplifier is used to compensate for the inherent inefficiency of the actual loop at the operating frequency. Overall, the system dynamic response is about +6 dB as compared to the dynamic response of a dipole. To aid in the direction finding process on strong signals, an internal 30 DB attenuator is provided. As the loop antenna presents a bi-directional response, tri-angulation may be required to eliminate the ambiguous signal direction. The line of site of the incoming signal is determined by listening for a signal null on the receiver or by watching the receiver’s S-meter.
-
product
Low-Noise Amplifier
CARM-02
HYPRES is proud to announce an Analog-RF Amplifier product. Using state-of-the-art low-noise amplifier and compact cryogenic cooler, the Cryogenic Analog RF Module (CARM-02) provides amplification with extremely low noise.
-
product
RF Plasma Generators & Amplifiers
100 W to 2400 W 13.56 MHz Analog/Digital, RS-232, USB interfaces Low Harmonic Distortion Automatic and Manual Gain Control High Speed Pulsing (Bursting) controls Compatible with T&C''''s Matching Networks GUI Software (complete PC control) Includes all essential RF power/communication cables and mounting brackets Air cooled (Air & Water 1200 W +) Half rack mount or stand alone versions Ideal for: Industrial, Scientific, and Medical Applications
-
product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - 3U VPX
Model 52690
- Accepts RF Signals from 925 to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal levels with up to 60 dB gain- Programmable analog downconverter provides I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Two 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Power Amplifiers
Triad’s line of RF and microwave Power Amplifier modules for extended range amplified radio applications set the bar for efficiency, linearity, and size-to-power ratio. We have designed hundreds of COTS modules for exacting frequencies up to 40 GHz . They offer high power levels into the hundreds of watts. And if a standard RF/microwave amplifier design does not fit your exact requirements, we’re specialists in creating custom-modified versions of any of our COTS power amplifier modules.
-
product
20GHz 30dBm RF Signal Amplifier
A10200
Model A10200 is an ultra-small footprint, ultra wideband, high power amplifier designed for high frequency, high power, signal amplification. With an ultra high bandwidth of almost 20GHz and up to +28dBm power into 50 ohms, the A10200 is the ideal complimentary amplifier to any signal source that needs an extended power boost for demanding applications.
-
product
Dual-Band RF Tuner and 4-Ch 400 MHz A/D with Kintex UltraScale FPGA - 6U VPX
Model 58891
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Four 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Four FPGA-based multiband DDCs (digital downconverters)- Two Xilinx® Kintex® UltraScale™ FPGA- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
OTP-Based Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
product
PXIe High-Speed Source/Measure Unit, 13 V, ± 1 A or 6 V, ± 3 A, 18 W
M9111A
The M9111A is a 1-slot, 2-quadrant PXIe module that provides stable, glitch-free sourcing and sinking, and high accuracy measurements. It offers high-throughput and measurement quality for design validation and production test of RF power amplifiers. With industry-leading output stability under extreme, dynamic load conditions and unmatched transient performance to dramatically reduce voltage droop due to pulse loading, the M9111A SMU speeds test time. The high-speed M9111A can change its output voltage, stabilize that voltage, and accurately measure current from Amps down to micro-Amps all in less than 1 ms so that you can move on to the next test as quickly as possible.
-
product
Space-Qualified Products
Teledyne RF & Microwave has a rich history with more than 40 years of space heritage without any in-flight failures. We serve the commercial, scientific, military, and government communities with best-of-breed space solutions. As one of the first companies receiving MIL-PRF-38534 Class K certification, Teledyne earned the space community's trust by commercializing and supporting the industry's most comprehensive line of space-qualified products, from components to solid-state power amplifiers to integrated microwave assemblies.
-
product
Components - Power Amplifiers (FPA)
FPA Series
FPA series driver amplifiers and power amplifiers are discrete and/or MMIC pHEMT device-based amplifiers that operate over the frequency range 18 to 110 GHz for high output power applications. The amplifiers are offered in two categories, standard and custom built up to 250 GHz.The custom-built amplifiers are offered in various RF interfaces, including standard waveguide or coaxial connectors, for convenient system integration. The optional input and output integrated isolators are available to further improve the port return loss.
-
product
2-18GHz Instantaneous Frequency Measurement Unit
DR024-F2
Teledyne Defence & Space’s Instantaneous Frequency Measurement (IFM) module, also known as a Digital Frequency Discriminator (DFD), offers high speed frequency measurement across the full operating bandwidth.The IFM measures the frequency of RF signal present at its input and presents a result at its output as digital data. The RF input signal is conditioned by an RF amplifier that provides sufficient drive for the frequency resolving circuits. The raw video from the resolvers is digitised and processed into the required output format. There is additional timing and control circuitry which initiates the measurement process and provides handshake data to the host system processor.
-
product
RF Power Amplifiers < MMICS
Macom Technology Solutions Holdings Inc.
MACOM is continually enhancing and expanding its MMIC power amplifier product portfolio to meet customers’ demanding technical challenges by leveraging state-of-the-art foundry technologies and proprietary in-house processes. MACOM partners with today’s leaders in Test and Measurement, SATCOM, Aerospace and Defense, Public Safety Radios, Wired Broadband, and Industrial Scientific and Medical applications to deliver industry leading, high-performance MMIC solutions in bare die and high performance packaging.
-
product
I/Q Downconverters/Receivers
In-phase quadrature (I/Q) downconverters integrate an image reject mixer, a low noise amplifier, a 90° hybrid, and an LO buffer amplifier in one package. These devices are used in receiver applications to downconvert radio frequency (RF) signals to the desired intermediate frequency (IF) while ensuring low noise and high image rejection performance.
-
product
Power Sensors
RTP5006
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 6 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements.This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
product
SMT & QFN Products
PMI offers custom surface mount (SMT) and QFN packaging for many types of devices. SDLVA's, Log Amplifiers, Phase Shifters, Attenuators, Switches, as well as Low Noise Amplifiers. PMI also offers multifunction options in a single QFN package such as Limiter / LNA or LNA / Detector. PMI has the experience to offer custom devices that meet your specific control function at high frequency. Mounting and integrating high frequency RF devices take skill and experience such that the package itself does not degrade the RF signal. PMI has the experience in selecting the proper package, integrating the RF devices and providing the required testing.
-
product
Low Noise Pre-Amplifiers
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
product
High-Speed, Fiber-Optic Reference Transmitters
Thorlabs' Reference Transmitters are designed for high-speed fiber optic test and measurement applications. They are fully-integrated and user-configurable solutions based on proven lithium niobate (LiNbO3) modulator technology driven by high-fidelity RF amplifiers.
-
product
RF Amplifier Modules
Analog Devices RF amplifier modules offer high linearity, low noise figures, and low phase noise, as well as low power consumption. These devices are all fully specified over frequency and temperature for use in a variety of applications.
-
product
Gain Block Amplifiers
RF gain block amplifier from Pasternack is featured in our extensive in-stock RF amplifier selection. Our connectorized gain block RF amplifier uses SMA connectors. This SMA gain block amplifier has a minimum frequency of 10 MHz, a maximum frequency of 3 GHz and a typical gain of 20 dB.
-
product
Microwave System Amplifier, 2 GHz to 26.5 GHZ
83018A
The Keysight 83018A microwave system amplifier is a compact, off-the-shelf amplifier designed for systems designers and integrators. This amplifier provides power where you need it to recover system losses and to boost available power in RF and microwave ATE systems. The ultrabroad bandwidth from 2 to 26.5 GHz allows the designer to replace several narrow bandwidth amplifiers with a single Keysight amplifier, eliminating the need for crossover networks or multiple bias supplies. The standard Keysight 83018A includes internal directional detectors for external leveling applications. With excellent noise figure relative to its broad bandwidth and high gain, this amplifier significantly improves system noise figure and dynamic range. The Keysight 83018A comes equipped with a low profile heat sink, an integral mounting bracket, and a two-meter dc power supply cable. Thermal characteristics and power supply design allow fast, easy integration into most measurement systems.
-
product
Power Sensors
RTP5518
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 18 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements. This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
product
Limiters
Macom Technology Solutions Holdings Inc.
At MACOM we offer a complete line of RF and microwave limiters, LNA/limiters and limiting amplifiers up to 18 GHz. These products use the latest thin-film hybrid manufacturing techniques to obtain the highest levels of performance, repeatability, reliability and cost-effectiveness. Using the latest technology available in the industry for silicon and GaAs FET MMICs, these products are ideal for multi-market and aerospace and defense applications.
-
product
RF Amplifier
SA822
Hangzhou Softel Optic Co., Ltd.
SA822 860 MHz outdoor distribution amplifiers are mainly used for bidirectional trunk transmission of CATV television image signal, digital TV signal, telephone voice signals and data (or compressed data) signal.
-
product
Power Amplifier
MS 2011
Power Amplifier is used to amplify the RF signals from low power to 100 Watts of RF carrier power to 400 Watts Peak envelop power (single side band operation). Outputs are filtered. This system is controlled through microprocessor and it has RS485 interface.
