Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
G12x Slide Mount
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. The G12x uses the same platform and slides as the G12, providing support up to 180 lbs (81 kg) to accommodate the largest fixtures. G12x accepts ITAs designed for both the G12 and G12x.
-
product
VOA DWDM with EDFA With VOA, EDFA Dense Wavelength Division Multiplexer
DWDA-1000 (100GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DWDA-1000 series is integrated by DWDM, VOA and EDFA module in a 1RU or 3D rack. Each channel of DWDM with a high-resolution factor electronic control adjustable optical attenuator will adjust and equilibrium the power. The insertion loss, power loss because of the channel equilibrium of DWDM will be amplified and compensation by the build-in gain flatness EDFA. Compact and simple device structure, thereby reducing the connections between devices to improve the index and reliability of the system. Can be used in DWDM system power equilibrium, optical add and drop multiplexed (OADW) flexible and expediently.
-
product
Data Logger
MS6-Rack
The complete solution for monitoring of temperature, humidity and other values. For mounting to 19" rack - one rack unit 1U. Enables to build in the optional MP016 output relays module with 16 relays - see Optional accessories.
-
product
CompactPCI 4U 84HP 8 Slots
Hartmann CompactPCI 4U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model comes with two 300W cPCI hot-swap power supplies and provides a 8 slot 5V I/O 9U monolithic (6U cPCI) backplane for horizontal mounting of boards.
-
product
AC Power Supply and Frequency Converter
P Series
The P Series AC Power Supply and Frequency Converter for your test bench or test rack delivers clean regulated AC power in a (2U) 3.5" high and (3U) 5.25” high bench top unit that easily converts to rack mount, for far less cost than competitive models.
-
product
Remote Cabinet and CO Splitters
3000 Series
Comtest's 3000 Series splitters are designed specifically for the European market. Their all-front connectors allow them to slot conveniently into ETSI racks at CO or a remote location—without the need for swing shelves. Cards are available for both POTS and ISDN and are compliant with ADSL2+ and VDSL technology.
-
product
Broadband Power Amplifier
PAS-08025-200
* Solid State Power Amplifier* Small Signal Gain: 50 dB typ.* Rack Mount Case (Optional)* Internal Cooling Fans* Type N Connectors
-
product
GPIB To Serial Miniboxes™
ICS's GPIB to Serial Minibox™ Interfaces are fully enclosed for benchtop or rack mount applications. The GPIB to Serial Interfaces are available for transparent data transfer and with smart firmware to add an IEEE-488.2 interface to any serial device
-
product
Digital Lab 30W – 300W Regulated DC Power Supplies
- 19” Rack Adaptable – 3U High Digital Output Metering 3 Digit DPM- Constant Voltage/Constant Current Operation- High Stability and Close Regulation ±0.01%- Proven Reliability and Endurance- 3U High- Remote Sensing Facility for 5A & Above Rating Models
-
product
Hot Swap, Fault Tolerant, Ultra Reliable Power Supply
Series HSP
The Kepco HSP series provides mission critical power. HSP comprises a group of twelve models, eight 1000 watt power supplies with outputs from 3.3 volts to 125 volts and four 1500 watt power supplies with outputs from 24 volts to 125 volts. All models feature current-sharing for parallel redundant N+1 operation. Models with the or-ing diode, option R, are capable of hot swapping when plugged into Kepco¹s RA 60 series rack adapter. Models with a digital meter, option M, are also available (see photo, right). A mechanical keying scheme allows the user to define which power supply will plug into a specified slot in the housing. Output voltage and current limit settings are adjustable from the panel and may be remotely adjusted.
-
product
Rack Mount Osprey Chassis 5.25" Qbus
97106-Q
5.25" high by 19" wide by 20" deep (134 x 483 x 508 mm), this chassis is FCC/CE certifiable**. A quad-height Qbus backplane, cooling fans, and slides are provided, diskette and hard drives (two visible 5.25" and two hidden 3.5" bays), and up to four quad-height Qbus compatible cards.
-
product
Data Center Load Bank
Mosebach Manufacturing Company
Mosebach’s Data Center Server Rack load bank, the SR family, is ideal for commissioning data centers. There are multiple models for varying voltages and power levels. The unit has a variable fan speed control which allows you to fine tune as desired.
-
product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, LL/S/C , Programmable Amplitude Balance
LS-16A-R1-24SLSC
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
product
Electrical Safety Analyzer
19032
Chroma Systems Solutions, Inc.
Our Electrical Safety Analyzers combine Hipot, Insulation Resistance ( IR), Ground Bond (GB), Leakage Current (LC)/AC LC/DC LC, and Dynamic Function Tests. Savings can be up to 50% of production line space by not having to purchase and rack several safety test instruments. It also increases efficiencies of electrical safety testing and reduces associated labor costs.
-
product
Rack Mountable Video Test Generator
804A
The Teledyne LeCroy rack mountable quantumdata 804A Video Test Generator is optimized for testing modern HDMI HDTVs. The 804A Video Generator support testing Ultra HDTVs in manufacturing at 4K resolutions at pixel rates up to 300 MHz. This enables testing ultra HD TVs with 4K resolutions at 24/30Hz with 4:4:4 pixel sampling and encoding as well as 4K resolutions at 50/60Hz using HDMI 2.0 using HDMI 2.0 4:2:0 pixel sampling and encoding. The 804A also supports testing with HDMI 2.0 21:9 format resolutions at or below 300 MHz.
-
product
26 lane, 26 port, PCI Express
PEX88024
The new PEX88000, PCIe Gen 4.0 switch family builds on the longevity of the PEX series of switches, now spanning 12 families. The PEX88024 switch allows Data Center and Cloud Providers to build flexible, scalable rack infrastructures, along with other advantages such.
-
product
HDG and OBS Track Select Panel
TA-260
Universal Heading and Track Selector Panel This panel provides a synchro transmitter for Heading and a synchro resolver for Nav converter alignment. The synchros are mounted on industry standard 18:1 dual speed drives for maximum accuracy and repeatability. This unit can be used to calibrate both manual and automatic converters. This panel provides a rear mounted interface connector as well as front mounted tip jacks for independent breakout if so desired. The TA-260 also provides two discrete switches associated with the resolver configuration. The 30Hz/400Hz switch is provided to allow the resolver to be properly compensated for the type of Nav converter to be aligned. The second switch allows you to open or short the resolver rotor lead as may be required by some newer GPS equipment. This panel is lightweight enough for portable use or may be rack mounted.
-
product
50 lane, 50 port, PCI Express
PEX88048
The new PCIe Gen 4.0 PEX88000 series from Broadcom builds on the longevity of the PEX series of switches, now spanning 12 families. The PEX88048 switch allows Data Center and Cloud Providers to build flexible, scalable rack infrastructures, along with other advantages.
-
product
6GHz Single Channel Signal Generator 19" 1U Rack Module
LS6081R
The LS6081R, 6GHz Single Channel RF Analog Signal Generator, offers industry leading performance, in a 1U, 19” rack-mounted box. The LS6081R features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS6081R was designed to offer excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
product
Digital Processor
DP7000
The DP 7000 Digital Processor with 40/100G Ethernet or 169G Interlaken protocol compatible MPO/MTP® Optics, designed for evolving markets such as Real-Time Stream Processing for High-speed Data-acquisition (DAQ), High Performance Computing (HPC), Machine Learning, Data Center Infrastructure, AI Processing and Network applications. The board is 8U form factor, 322.25 mm x 280 mm x 6 HP (L x W x H), single slot AXIe or AdvancedTCA® blade, ideal for multi-slot 19″ rack mount system integration. In AXIe form factor it provides up-to Gen3 PCIe® backplane connectivity.
-
product
Load Cell Indicators
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicator will need to be mounted in to a case or control rack for safe use.
-
product
LXI Microwave Multiplexer, 50Ω 36-Channel 1-Bank 18GHz SMA
60-891-001-001
The 60-891-001-001 36 channel Microwave Multiplexer is suitable for switching 50Ω signals up to 18GHz. Connection is by front panel SMA connectors. This multiplexer is also available in a 50Ω BNC version which can switch signals up to 4GHz (model 60-891-001-002). The multiplexer has an extremely high level of performance with low VSWR, very high isolation, low loss and high power handling. It is ideal for switching 50Ω systems for HF up to microwave frequencies. It occupies 2U of rack space, providing a compact switching solution.
-
product
Capacitor Tester
MIG1212CAP
MIG1212CAP is specially designed for high voltage test on X / Y capacitors with impulse voltage approximate 1,2/50 µs up to 12 kV in accordance with IEC 60384-14 Ed.4. The MIG1212CAP comprises two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape of approximate1,2/50 µs and are combined in an 8 unit high 19" rack. IEC 60384-14 and EN 132400 define the generator.
-
product
Serial-to-Daq Minibox
Model 2367
* 2367 provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Module. * DB-25 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * The 2367 is packaged in a CE approved Minibox™ metal case to minimize EMI/RFI. * 1 U high Rack Mounting Kit mountsone or two 4867s.* Plug-on Terminal Board simplifies wiring connections.* Includes Universal Power Adapter and 62-pin mating connector.
-
product
Rack Extender Kit, G12x, 1.5" Deep
310113519
The Rack Mount Extender Block Kit is used for mounting to racks with recessed mounting rails recessed more than 1.” It is made of aluminum with a black anodized finish. NOTE: Used only with slide mounted G12x Receivers.
-
product
20GHz Single Channel MW Signal Generator 19" 1U Rack
LSX2091R
The LSX2091R is a 20GHz Single Channel Microwave Signal Generator, offers industry leading performance, in a 1U, 19” rack-mounted box. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The design offers excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
product
Ethernet to Relay Minibox™
Model 8064
* Model 8064-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.*Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 8064s.* Optional terminal board and terminal strip for easy connections without soldering. See the Ethernet Accessory page.
-
product
Extended Rack Autosampler
XLR‑860
See why users call CETAC Autosamplers the best on the market. Put the most reliable, longest-lasting autosampler to work in your lab for the seemingly endless demands of sample analyses. Whether your lab is small, mid-sized, or very large, there’s a model to meet your needs!
-
product
Winding Resistance Meter 15Amps, 2 Channels Rack
WR14R
Raytech Digital Winding Resistance meter WR14 R is the rack mount version of the WR14. They are designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
product
Continuous Gas Analyzer
CT5400
Multi-component continuous gas analyzer combines QCL and TDL technologies in a single rack mount enclosure to measure process gas and monitor emissions from sub ppm to % levels. The CT5400 is ideal for measuring NOx, SO2, CO, CO2, CH 4, NH3, O2, HCl and other combustion gases identified as pollutants, ozone depleting, or responsible for global warming.
-
product
VPX Air Transport Racks
Air and conduction cooled ATR enclosures for rugged VPX deployments.
