Filter Results By:
Products
Applications
Manufacturers
Switch Test
Make, break, or change the connection of a circuit.
- Pickering Interfaces Inc.
product
PXI Single Bus 32-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-501
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Mass Interconnect
Mass Interconnect is a mechanical interface that simplifies connection between the power supplies, instruments and switching to the Device Under Test (DUT) in a test environment. In the illustration here, a test receiver is connected to the front of the modular instrumentation, in this case, a PXI chassis.
-
product
Data Acquisition Switch System
M300
No matter the product performance test in the R & D stage or the automatic test in the production process, for the application of multiple test points and multiple signal measurement, the M300 series data acquisition / switch system with modular structure combines the precise measurement function with the flexible signal connection function, and can provide a wealth of test measurement solutions.
-
product
PXI 36 Channel Data Comms MUX, 96-pin SCSI
40-735-912
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. This 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
product
High Throughput 1 ns Pulsed IV Memory Test Solution
NX5730A
Precise and fast characterization of new memory, such as spin transfer torque magneto resistive random access memory (STT-MRAM) from DC to high-speed pulsed IV measurement on silicon wafers Apply accurate and high-speed pulsed voltages (down to 1 ns pulse) to magnetic tunnel junction (MTJ) for STT-MRAM and precisely measure the resistance of MTJ Perform all typical MTJ characterization tests in one solution10 to 100 times faster cycle test, such as a bit error rate test (BERT)Capture and visualize MTJ switching waveforms clearly during the writing pulse Dedicated solution with Keysight Technologies’ technical expertise
-
product
Switches
Whether you are performing high-accuracy, low-speed measurements on a dozen test points or high-channel, high-frequency characterizations of integrated circuits, National Instruments delivers a flexible, modular switching solution based on PXI or SCXI to help you maximize equipment reuse, test throughput, and system scalability.
-
product
PXI Very High Density Versatile 2 Amp Multiplexer
40-612A-002
The 40-612A Very High Density Versatile Multiplexer module features a wide range of software selectable switching configurations. It is especially useful where a number of high density multiplexers are required with the option of easily altering the channel count as a test system evolves. Typical applications include signal routing in ATE and data acquisition systems. The 40-612 module uses high quality electro-mechanical relays, connections are made via a front panel 160 pin DIN41612 connector. The module can be software configured into one of a large number of different multiplexer modes. Relays allow the multiplexer banks to be set in 1 or 2 pole mode and inter-bank switching enables the channel count to be increased up to a maximum of 128
-
product
High Speed-Large Current DC Electronic Load (CC/CV/CR/CP)
PLZ-4WL Series
While the PLZ-4WL series succeeds to the superior operability of our conventional model of the PLZ-4W series, the PLZ-4WL series realizes the high speed rise and fall time (slew rate of 50A/µs.) in the range of low voltage with large current. The PLZ-4WL offers six operation modes, and equips with various features such as sequence operation, switching operation, soft-start function, and time and voltage measurement. The PLZ-4WL applies not only for the conventional load test of the CPU power supply, but also it can be applied to even faster current response test. In addition, the PLZ-4WL is a space-saving design (about 50% less volume of the conventional model) that can save the facility space of the testing site, and it can be applied for the single cell testing of the large scale rechargeable battery.
-
product
Coaxial Switch, DC to 40 GHz, SPDT
8765D
The Keysight 8765 family of switches is designed for microwave instrumentation and ATE systems and features excellent electrical and mechanical performance. The Keysight 8765D is equipped with SMA connectors and operates from dc to 26.5 GHz with 3.5mm connectors and 40 GHz with 2.4 mm connectors. Option 292 can be ordered with Keysight 8765D. It is available with voltage option covering any drive voltage between 4.5 volts and 32 volts dc. Where performance data are required, Option UK6 includes a printout of test results. This switch is designed from the ground up for maximum dependability and performance. It is designed to operate within its specifications for more than 10,000,000 cycles.
-
product
MTM-Relay: 4-Channel Solid-State Relay (SSR) Module
SOLID STATE: The MTM-Relay is a key component to automated manufacturing test systems that require switching of industrial control voltages. Features four software-controlled solid-state relays (SSR) that can handle up to 60V and 6ADC/RMS.
-
product
PXI Matrix Switch: 8x32, 1-Wire, 100Vrms/2A, Armature Relays
M9122A
The M9122A is an 8x32 full crosspoint switch matrix offering high-voltage switching in a high-density PXI module. This module allows for higher voltage switching of multiple channels in a single instance. Any row can be connected to any column, making it ideal for routing instrument signals to the device under test. This module is configured with a common ground. The durable armature switches are capable of switching up to 100Vrms, with up to 60W of power. The 8-wide bus can be used to route signals between your instruments and the device under test. Choose from the durable connector block or standard cable connections.
-
product
PXI 3A Power MUX BRIC, 48-Channel, 6-Pole
40-571-406
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Test Equipment Grade Switches
Multi-Tech Industries also manufacturers a line of quality instrument-grade electromechanical switches for commercial, industrial, military, institutional and OEM applications. Rotary switches (open frame, enclosed frame), thumbwheel, keyreader and other types are available to be integrated into your process controls or test instrumentation. Standard and custom switch designs can be modified to meet specific customer requirements.
-
product
PXI 2A 32xSPST High Density Power Relay Module
40-137-101
These Power Relay Modules are suitable for applications requiring power relay switching with high density. This version features 2A current and voltage to 110VDC/250VAC, they are configured as Single Pole Single Throw (SPST). Connections are made via front panel mounted 37 or 78-pin D-Type connector.Along with this 32 x SPST version, the range also includes a 39 x SPST, 2A version and a 16 x SPST, 5A version - go to Also in the Range above to learn more.Typical applications will be found in Automotive Test, Aerospace Test and Power Cell Test applications.
-
product
Switch Stick Test Equipment
Hanco units provide a full high voltage electrical test as required by OSHA. Front-loading, top-loading and portable units are available.- Sticks can be tested wet or dry.- Test units are available to test sticks up to 14 or 21 feet maximum length or up to 8 feet for the portable unit.
-
product
PXI Switch Matrix Modules
From low density to high power - we have the PXI matrix switch modules you need. PXI matrix switch modules deliver low, medium and high-density switching of multiple channels in a single instance. They are organized in rows and columns to provide maximum flexibility, allowing you to connect any row to any column, making them ideal for routing multiple signals between your device under test and your instruments.
-
product
AFDX ® /ARINC664P7 Networks Test, Simulation, Monitoring & Analyzer
ACE-FDX-3U-2
AFDX®/ARINC664P7 Test and Simulation module for PCIe x1 with 2 full duplex ports programmable for 10/100/1000 MBit/s. Versions available for both Airbus and Boeing variants of ARINC664P7. Test, verification and simulation of AFDX®/ARINC664P7 End Systems, Switches and Networks. Support for Single or Redundant AFDX®/ARINC664P7 operation. Support for Boeing ARINC664 extensions for EDE at the hardware interface layer.
-
product
PXI 8x9 RF Matrix 250MHz 75 SMB
40-725-751
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
product
70-440V AC Non-Contact Voltage Detector With Buzzer
1966A
Peaceful Thriving Enterprise Co Ltd
*Check voltage on 70-440V AC.*With CE, cUL and RoHS Approval.*Operates by two LR44 1.5V batteries.*LED will glow if AC voltage is present.*Check for proper ground connection of electrical appliance.*Test electrical lines, cables, sockets, fuses, switches and etc.
-
product
LETIS
Power amplifiers that are universally used for radiated immunity testing either cover the range below 1GHz or the range above 1GHz. This means that if the test requirement extends both sides of this 1GHz point, the power amplifier needs to be changed over. Genrally, this involves three connections... The LETIS handles all these connections automatically. Each is switched via a high performance RF relay under the control of a USB interface. Software issued with the Laplace Synthesisers automatically detects the presence of a LETIS and handles the switching automatically.
-
product
Keysight Dual/Quad 4x8 Reed Matrix for 34980A
34933A
The Keysight 34933A module for the 34980A Multifunction Switch/Measure Unit gives you the most flexible connection path between your device under test and your test equipment, allowing different instruments to be connected to multiple points on your device under test at the same time. Dual 4x8, 8x8, or 4x16 2-wire configurations 64 2-wire or 128 1-wire cross-points High-speed reed relays Connections to the internal DMM Expandable via four 2-wire analog buses Relay counter ±150 V peak, .5 A switch, 1.5 A carry current
-
product
Digital Engine Analyzer
KT-7182
0.5" (13mm) LCD Max. indication 1999 or - 1999. Engine TACHO & DWELL MEASUREMENT. Polarity: Bi-polar by automatic switching. "-" indicates reverse polarity. Over-input: Indication of "1" or "-1" Complete with test leads, 9V battery, and protective rubber holster
-
product
30 Amps, 100 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP031
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
PXI 3A Power MUX BRIC, 5-Channel, 48-Pole
40-571-005
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
eBIRST™ – Switching System Test Tools
The eBIRST toolset consists of four different tools that support 200-pin LFH, 104-pin, 78-pin and 50-pin D-type connectors and a set of adaptors that allow connection to other connector types. A supplied application program controls the eBIRST tools via a USB2 port that also provides the tool power and controls the switching system using a Test Definition File to define the test sequence.
-
product
Switching Matrix
MUX
The Analog Signal Switch Unit serves as a 6-bus interconnect for 128 pins each to the Analog Measurement Unit (AMU05) for the In-Circuit test.
-
product
Multiplexers
Capable of performing the necessary switching between test points of the device under test, to give access to low frequency measuring instruments, in electronic test systems based on tool receivers.
-
product
PXI 3A Power MUX BRIC, 16-Channel, 6-Pole
40-571-402
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
LED Driver Automatic Test System
ATE-2
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection. •It can test 4 LED drivers input and output at one time. •The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer. •Enable to print out the series number and parameters of sub-quality products by working with a micro-printer, •Enable to achieve the bar-code record function by working with a bar-code scanner. •The test report can be saved as Excel file for consult, statistic and analysis purpose. •Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
-
product
IEC60884 Fig22 Plug Socket Covers Pendulum Impact Test Apparatus
CX-BC22
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig22 plug socket covers pendulum impact test apparatusMeet the standard: IEC884-1 Figure 22-26,, IEC60068-2-75Uses: Suitable for household and similar plugs and sockets, wall mounted mounting boxes, screw glands, covers, switches and other electrical accessories for mechanical strength test
-
product
DC Power Supply
PDS Series
This series of products is programmable DC switching power supply with high accuracy and single output. It is light and compact, adjustable in voltage and current, and has multiple operating modes. The whole system is completely controlled by the microporcessor (mou), and can easily use the communication interface (re-232) to connect with the computer (PC) to meet the user's requirements for automatic testing and automatic control. The software instructions are completely in accordance with the scpi command. The format makes it easy for users to develop automatic test and automatic control applications. Due to the full digitalization of the system, the data input is completely controlled by the keyboard and knob, which is fast, accurate, and convenient. Can be widely used in electronic product development, device testing, communications industry, laboratories and scientific research institutions.
