- Pickering Interfaces Inc.
product
EBIRST 68-pin Male SCSI Termination Fixture
93-015-103
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Supported Test Systems
TTCI is a leading solutions provider of application development for test systems from Seica, Keysight, Teradyne, Digitaltest, and XJTAG. We offer a wide variety of testers and test solutions to meet your needs. Our Seica Pilot and Digitaltest Condor flying probe systems can handle all of your low- to mid-volume production, prototypes, and PC boards with accessibility issues. The Keysight 3070 and Teradyne TestStation can address your larger production runs and fixture requirements. In addition, we can also address your functional and boundary scan needs.
-
product
Deep And Sloped Pan Fixtures
Line of deep and sloped pan fixtures for general purpose/system non-specific pcb test applications. H+W Test Products manufactures test fixture products for in-circuit, functional and combinational testers for users of automated test systems (ATE) such as Aeroflex, Agilent (HP), Checksum, Factron, Teradyne (GenRad), Test Research (TRI) and Testronics.
-
product
Wireless Test Fixtures
At Forwessun, we have vast experience in designing and delivering wireless in-circuit test (ICT) fixtures. We have experience in providing fixtures tailored to the unique needs of various different industries. While our primary customer focus has been on full and half-bank fixtures for the HP3070 system, we offer bespoke solutions for other platforms as well including GenRad, Teradyne, and SPEA systems.
-
product
Vacuum Test Fixtures
Vacuum fixture kits for Pylon block fixture, Teradyne, Keysight, Digitaltest,Seica, Cobham (Aeroflex), ATX exchangeable system.
-
product
CAD / BOM Translation Software
ProntoTEST-FIXTURE
In minutes the Unisoft ProntoTEST-FIXTURE software translates CAD and Bill of Materials (BOM) files into real reference designators, netlists, X/Y component pin geometries, values, tolerances, part numbers, etc. This data is then used by Test Engineers to program their ATE (Agilent/Hewlett Packard "board & board x/y", Teradyne "ipl", Genrad ".ckt"), MDA, and flying probe test equipment and design the "Bed of Nails" test fixtures.
-
product
Fixtures, Programming & Test Services
Comware Technical Services, Inc.
Fixtures and programming services are available for Agilent, GenRad, and Teradyne testers. Working from CAD data, a program can be created in only a few days allowing for fast and cost effective testing of your products. Engineering services are available for fixture revisions or repairs.
-
product
In-Line / Board Handler
Circuit Check’s in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading ICT handlers including Keysight 5i, Teradyne TSh Multi-Site, IPTE and Pematech. Circuit Check is the go-to partner for in-line functional test fixtures to speed production throughput.
-
product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
In-Circuit Test (ICT) Fixtures
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Stopper kit includedYAVCANCON2 for fixture identification not included
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
Fixture Self-Test Controller and Calibration Check
AQ818
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
product
Test Fixtures
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
product
Magnetizing Fixtures
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
product
Test Fixture
N1295A
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
product
ICT Test Fixture
It can be produced in our overseas branches which are Thailand ,China and India.High precision test fixture can be produced.Test fixture for other brand testers can be produced.
-
product
Latch-on Test Fixtures
Latch-on Test Fixtures provide a convenient way for production personnel to quickly and reliably make electrical connections to a product for programming or final test. These custom fixtures eliminate the need to hand-wire products in order to power them up and communicate with them. Typical applications for latch-on test fixtures are metering devices, control panels, and any type of controls that connect via terminal strips.
-
product
Customized Test Fixtures
Test fixture is a device designed to mount a device under test (DUT), equipment under test (EUT) and unit under test (UUT) in place and allow it to be tested by being subjected to controlled electronic test signals and procedures.
-
product
Custom Test Fixtures
Cortek Test Solution’s design capabilities range from very basic to extremely sophisticated solutions. Developing custom test fixtures demands more engineering time as well as an in-depth knowledge of mechanical design, pcb test methods paired with precision machining. Our experienced engineers will evaluate your requirement and design innovative mechanical test fixtures to meet your application needs in both the R & D and production environments.
-
product
Stand-Alone Test Fixture
MA 2012/D/H/GR2270/71
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,00 kg
-
product
Test Fixture
16047E
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
product
Functional Test Fixtures
Intrinsic Quality delivers turnkey standalone Functional Test fixtures and Windows based functional testers that are custom engineered with innovation and reliability to meet your testing needs. Our experience and expertise ensure a production ready functional test solution that is cost-effective, on time and on budget. Our broad range of test solutions includes simple continuity testers to complex microcontroller assembly testers. Our customers include military, aerospace, automotive, medical and consumer OEMs. We serve the needs of low volume high mix CEMs and off shore high volume manufacturers.
-
product
Mechanical Test Fixtures
MMI series man-machine interface
Designed to meet the needs of the most discerning customers and the latest market demands, our MMI series guarantees a natural posture for both the operator and the sitting position when performing the test on the adapter. The newly developed lever mechanism, which has been registered as a utility model, is specially adapted to the hand movement of its employee and ensures a heart-loving strain on the operator.
-
product
RF/Wireless Test Fixtures
Test‐Head Engineering develops and manufactures RF Test Fixtures which allow the testing of RF and Wireless modules and components.
-
product
Compression Set Fixture
ASTM D395
ASTM D395 Compression Set Fixture is to test rubber under constant deflection in air.
-
-
product
Flex Test Fixtures
FTFs are test fixtures which are dedicated for testing flex-based components and assemblies such as displays, touch panels and more. A weak spot in a typical functional test system is the method to connect DUT flexible cable to a circuit board where the simple method of attaching the flex directly with an ZIF or LIF connector fails.
-
product
System Test Fixture
Chassis Level Test Fixture, Set Box Test Fixture, and more by IST Engineering
