Filter Results By:
Products
Applications
Manufacturers
Test Cases
sets of events to find the performance boundaries of a design.
- Pickering Interfaces Inc.
product
eBIRST™ – Switching System Test Tools
The eBIRST toolset consists of four different tools that support 200-pin LFH, 104-pin, 78-pin and 50-pin D-type connectors and a set of adaptors that allow connection to other connector types. A supplied application program controls the eBIRST tools via a USB2 port that also provides the tool power and controls the switching system using a Test Definition File to define the test sequence.
-
product
Mass Interconnect
Mass Interconnect is a mechanical interface that simplifies connection between the power supplies, instruments and switching to the Device Under Test (DUT) in a test environment. In the illustration here, a test receiver is connected to the front of the modular instrumentation, in this case, a PXI chassis.
-
product
Test and Check Advanced Kit w/ DL479/ CD100A/ EM152/ PDT550
TACK20
UEi Test & Measurement Instruments
Convenient Advanced Test and Check Kit, includes True RMS Clamp meter, Combustible leak detector, Dual input manometer, NSF waterproof thermometer, K-Type pipe clamp adapter, K-Type Input jack adapter, Carrying case
-
product
Averaging Extensometers for ASTM D5656 Shear Tests
Model 4013
Jinan Testing Equipment IE Corporation
The Model 4013 extensometer meets the requirements of ASTM D5656 for measuring the strain properties of an adhesive in shear. It uses different contact point spacing compared to the extensometer shown in D5656. This makes it much easier to mount and eliminates the slippage problems associated with the design shown in the ASTM standard. The Model 4013 is available with all of Epsilon’s temperature configurations. It has a 3.0 mm (0.12 inches) full scale measuring range. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 4013 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Large Earth Resistance Tester
WA 180
Wuhan Sangao Electrical Test Installations Limit Co.
WA180 Type Large earth resistance tester,To test substation earthing network(4Ω), Hydroelectric and Thermoelectric Power Plant,microwave(10Ω),lighting rod(10Ω)etc.Using new type variable frequency AC power supply, And adopts microcomputer control and signal processing measures, Solved the problem of interference of the testing process, To simplify the test procedure, To improve the precision and accuracy of the test results, reducing test personnel's the labor intensity and the cost of testing.The instrument can be used to test all kinds of power frequency earth resistance,contact voltage,step voltage etc frequency power parameters and soil resistivity. The instrument adopts the different frequency Anti-interference resistance technology, under strong interference environment accurately measured the frequency under 50Hz data.The maximum test current is 5A,it will not cause the earth device potential too high,and it also has strong anti interference ability, so it can be measured in the case of non power.
-
product
Custom Industrial Torque Sensors
Datum Electronics are able to provide both modular and custom designed torque and rotary strain measurement solutions, which can be complete as one off or as fully integrated OEM solutions.In many cases, it is better to use an existing shaft or test rig and use custom industrial sensors instead. This process reduces the cost of fitting a conventional torque transducer and it improves the torque measurements, taken by maintaining the dynamics of the driveline.
-
product
Load Cell Power Supply Module
MODEL PSM-F10
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
product
SoC Verification
TrekSoC
TrekSoC automatically generates self-verifying C test cases to run on the embedded processors in SoCs. This verifies your chips more quickly and more thoroughly than an external testbench, hand-written C tests, or running only production code on the processors. TrekSoC's generated test cases target all aspects of full-SoC verification and work in a variety of different environments.
-
product
Test Automation System for Engine Testing
STARS Engine
With a wide range of user-friendly features, STARS Engine can run the most complex of tests with a simple press of a button making your test operation effective and efficient and above all, reliable. STARS provides all the features you need to run a wide range of Engine Test Programmes from simple manual testing to dynamic automatic tests, all from a single, simple to use user interface. STARS is designed to be run in either stand-alone operation for a single test stand or as a cluster of systems to allow a test field to be run more efficiently. In both cases the user works in the same way and uses the same interface.
-
product
Closed-Link Field Test Kit
630
TESCO’s Closed-Link Field Test Kit (Catalog No. 630) with Power Factor has been designed to reduce the weight of field test equipment to the lowest possible limit when testing electric meters without potential links or with the links closed. The unit is protected within its ergonomic carrying case by a durable powder coated aluminum shell. The total weight of the meter test kit including leads, and digital reference standard is only 30 lbs! The test kit carrying case also incorporates ample storage space for the cable set and other tools.
-
product
Cloud based Requirements Management & Bug Tracking Service
ReQtest
Our software testing tool ReQtest offers a complete module for test management. Plan your testing by writing test cases and checklists, execute them by sharing with your test team, and follow the progress in real time to see how the tests are going. ReQtest offers great support to easily search, filter and group your bug reports and presenting them in a useful way.
-
product
Surface Resistance System Kit
PRS-801RM
- Perform Point-to-Point and Resistance to Ground Measurements from 0.01 Ω to 200 Teraohms- Accuracy of ±2% from 1.00 Ω to 9.99x1010Ω- Measures in accordance with ESD TR53, ANSI/ESD S4.1, ANSI/ESD S7.1, ANSI/ESD STM97.1 and others- Constant Test voltages 10V and 100V meeting ANSI/ESD S20.20- Operates using a Rechargeable Li-ion Battery Pack- Takes Approximately 8,000 Measurements on a Single Charge (480 hours typical)- Stores up to 999 Test Values Into Memory- Compatible with Prostat Connect 2.0 for Downloading into Excel®- Charging and Download via Standard Micro USB Cable- Includes 5lb Conductive Probes and Carrying Case- Certificate of Calibration Traceable to NIST included- 2-year Limited Warranty on Main Instrument
-
product
Accessories
Check out the full line of quality Amprobe accessories, which are field tested to help you get the most out of your Amprobe tools, including:*Rugged test leads of all types and sizes for Amprobe instruments*Current transducers for maximum accuracy and safety*Temperature accessories for surface, air/gas, or liquid temperature measurements*AC relays for low-voltage control circuits*Adapters, software, carrying cases and more
-
product
Premium Automotive DMM
597
*CATIII 1000 Volt / CATIV 600 Volt Approved & Safety Rated *Safe For Use on Hybrids and EV's *Highest Quality Auto-Ranging DMM Designed for Automotive Trouble Shooting *18 Test Functions, 48 Test Ranges *Peak Min/Max records transient voltages as fast as 1 millisecond *Min/Max Mode records variations in all functions *Also measures Temperature via Temp Probe in Both F and C *Milliseconds Pulse Width Measures Fuel Injector ON-TIME *Inductive RPM Readings for both DIS and Conventional Ignitions *Desirable 20 Amp Test Range - Dual Fuse Protection *Modern Design, the Protective Holster is Built Into the Housing *Data Hold, Auto Power-Off, + Trigger Adjust *Large LCD Display w/White LED Backlighting and 40 Segment Analog Bargraph *Blow Mold Case, Test Leads, K-Type Temp Probe, Inductive RPM Clamp and Instructions included *Waterproof to IP67 Standards
-
product
Contact Resistance Meter
PCRM200S
The Motwane Manufacturing Company
The Motwane make Contact Resistance Meter (Model:PCRM200S) is a digital micro-ohmmeter, specially designed to measure extremely low resistance in micro ohm. The Instrument is based on Kelvin 4-wire connection method for measurement of low resistance.The Current injection is fixed at 100A & 200A. Test information like current injected with measured resistance & voltage drop is displayed with real time data on large LCD with backlit.This User friendly Instrument and it's accessories are housed in easy transportation case. Advanced Windows based software isprovided for data downloading, analysis and report generation. Internal memory of 199 records is provided for onsite data storage withDate & Time stamping & Recalling facility. Thermal printer is the additional feature provided to print the test results.
-
product
Supernova
SuperNova Test Application Framework is an innovative, fully integrated test environment that addresses world-class test deployment challenges by simplifying access to high-end test capabilities, reducing time spent on analysis and customizations, and quickly meeting the most different test deployment use cases.
-
product
Auto-Ranging Digital Clamp Meter
DCM401
Expert Quality, auto and manual ranging clamp meter capable of voltage, current, resistance, diode, continuity, capacitance, frequency, duty cycle and temperature testing. Maximum jaw - opening diameter of 36mm, backlit LCD screen, auto power off and a useful inspection light. Supplied with test leads, temp probe, case and 3 x AAA batteries.
-
product
LCR Meter, Hand Held, 100 kHz, 2 kH, 20000 µF, 0.2 Gohm
72-10465
The 72-10465 from Tenma is a LCR meter in orange and grey colour. It features an easy to read dual LCD (40mm x 63mm) display measurement of 19999/1999 (main/auxiliary). It also has series and parallel measurement modes which can be used to select quality factor, loss factor, phase location angle and equivalent resistance of measure articles. Intelligent detection and five different test frequencies enable accurate readings for all sizes of capacitors and inductors. The user can also access the stored data on a PC with the included USB connection and interface software. The compact size and case make this unit far more portable than a benchtop meter.
-
product
Software UNIT TESTING product
C-TestIt
Unit testing, in the case of C, is understood as the ability to test a function regardless of the rest of the application.Unit testing is a complement to traditional testing, for those Customers who want to improve the quality of their software and therefore reduce future maintenance costs.
-
product
Clamp On Meters
Triplett Test Equipment & Tools
1000A True RMS AC/DC clamp-on meter with a backlit LCD display. It offers a large variety of measurement features including AC/DC Current, AC/DC Voltage, Resistance, Temperature, Capacitance, Continuity, Diode Test and NCV Detector. The rubberized overmolded housing provides impact and drop resistance in a sleek ergonomic design, and the user-friendly Auto Power Off feature helps maximizes battery life. With a CAT III 600V design, it provides superior resistance to damage from transient overvoltages in any demanding industrial setting. The Model 9325 is suited for a variety of industrial and residential applications such as security, electrical, HVAC installations and more. Includes test leads, Type K Temperature probe, 9V battery, and case.
-
product
Automatic Software Testing
Conformiq offers a next generation solution for automatic software testing. Our products fit the needs of Agile software development by adapting quickly to new product requirements and eliminating the time required for laborious test execution script maintenance during short sprints. Instead of using test cases, Conformiq users have a model, which describes the System Under Test, or the product you want to test.
-
product
Fatigue Testing And Certification
Fatigue engineering is subject to uncertainty, and data from well executed tests are used to validate conclusions made by analysis and to provide a basis for structural certification. Our staff have extensive experience in testing materials and components under slowly varying, static loads, and under rapidly varying cyclic loads. Tests under static loads are used to assess material properties or to assess the load-deformation behavior of structural components. Tests under cyclic loads provide time to crack initiation, time to failure, or measurements of crack growth over time. We have extensive experience in measuring fatigue crack growth behavior in metallic materials. Past programs have measured crack growth with microscopy and photogrammetry at the surface, cracked area with direct current potential drop, and through-thickness crack profiles with quantitative fractography. By assessing crack growth with a variety of experimental methods, we enable robust analysis validation for cases of complex cracking. Our capabilities in fatigue engineering allow for careful design of a fatigue test program. Whether the tests use constant amplitude loading or an irregular loading spectrum, we specialize in engineering the test that meet your needs. Much of our experience is in non-standard test programs, which require engineering to optimize the test setup. Few others match our capability and experience in fatigue test engineering.
-
product
Test Programming
Terotest offers a full test programming service for all of our Automatic Test Equipment. In many cases test programs can be generated from CAD data on the product or component under test, or from autolearn facilities within the test system. Such techniques maximise accuracy and test program fault coverage, and allow quick and easy test program generation.
-
product
Hardy Shaker
HI-903
This is our top of the line Hardy Shaker. It provides the ability to set the amplitude and change the frequency range without the amplitude changing. This automation makes conducting vibration tests easier. Tests can be conducted on multiple vibration transducers, and then the saved data can be transferred via USB Flash Drive to be displayed in an automated and customizable report using an Excel template on your computer. In manual mode, the vibration test level and test frequency can be set from 7 Hz to 10,000 Hz. The high accuracy instrument can display the vibration level in terms of g’s peak, velocity peak (in/sec or mm/s) or displacement peak-to-peak (mils or µm). The unit can support payloads up to 800 grams (see frequency limits in the manual). A built-in display reads the output sensitivity, which can be stored in memory. Complete testing sequences and data can be stored in memory for each tested sensor, the unit logs the data on the spot or stores it for later use. For testing of heavy transducers or at high frequencies, the HI-903 automatically corrects the sensitivity calculation for the effects of transducer mass loading. A built-in self-test program checks for accuracy of all calculations. The HI-903 has a built-in battery charger that can operate on 120 or 240 VAC. The unit comes in a rugged Pelican case.
-
product
LANTRACKER
PH-100/120
The Lantracker is a network tester, pin-by-pin cable tester, and tone generator all in one. As a network tester, it detects whether a network is active or inactive and displays network speed (10/100/1000 Mbps) in either case. It also flashes the network hub or NIC’s port light corresponding to the cable it is connected to, to show the cable’s port number. As a cable tester, it performs loop-back or remote tests of network, data, voice, and coaxial cables, displaying the results on a pin-by-pin LED display which moves from pin to pin automatically or manually. The Lantracker can be used to test cable or shield integrity, testing network function and speed, and tracing cable using its tone generator function (tone probe not included). Includes an adaptor for testing coaxial-F cable. Uses 1 9V battery.
-
product
AC Power Source
9420
AC Source with HiVAR Technology Ideal for ATE use in Aviation, Aerospace, Defense, Military/Mission Critical Testing, Manufacturing Test, Research & Development & More! The Model 9420 AC Power Source redefines selection of an AC Source by addressing how to compensate for reactive power from capacitive or inductive elements in the load. Often overlooked when sizing a source, reactive power negates some portion of nominal VA power in order to arrive at true power (Watts) that does the real work. Traditional AC sources list only their VA rating leaving it up to the user to figure out how much true power remains after reactive power reductions. In many cases that reduction is substantial and then requires selecting a much larger VA-rated source than originally anticipated. The increased cost and size penalties are often considerable.
-
product
Pressure Gauges
NOSHOK offers a broad range of pressure gauges that are engineered with state-of the art technology to provide excellent accuracy and reliability, and accommodate nearly every application. NOSHOK's industry-proven dial indicating gauges include dry and liquid filled, high and low pressure, process, and precision test gauges available with a variety of corrosion-resistant case type, lenses, connections and scale options.
-
product
Conformance Test Solutions 3GPP / Regulatory (CTIA / RED)
Only conformance test sytems from Rohde & Schwarz cover all relevant digital mobile device generations.The key to success is comprehensive access to RF, RRM, LBS and PCT test cases as defined e.g. for 5G NR in 3GPP TS 38.521-1 to -4 (5G NR RF), 38.533 (5G NR RRM), 38.523-1 (5G NR PCT), 37.571 (LBS).The Rohde & Schwarz conformance test solution portfolio consists of approved test platforms for device certification by GCF and PTCRB that support both TDD and FDD and all relevant 5G NR bands in both sub-8GHz (FR1) and mmWave (FR2) frequencies, as well as all frequency bands for LTE, WCDMA and GSM.
-
product
Conformance Test Systems
With an established market leadership position in GCF and PTCRB approvals for LTE-Advanced and all leading-edge technologies, Anritsu continues expanding its number of test case validations in GCF and PTCRB for Protocol, RF and RRM conformance testing. With increasing complexity of wireless technologies, Anritsu Conformance Test systems provide easy-to-use control software to maximize testing efficiency.
-
product
Pull Off Adhesion Tester
106
Applications for the Elcometer 106 Adhesion Test include paint or plasma spray on bridge decking, coatings on steel, aluminium, concrete etc.Supplied in a carry case - ideal for site testsHand operated - no need for a power supplyIncludes a cutter for EN13144 and ISO 4624 tests
-
product
Circuit Breaker Analyzer
CBA 3000
CBA 3000 allows any timing test, motion and speed analysis, multiple contemporary static and dynamic contact resistance measurements, both sides grounded (BSG) tests, undervoltage condition test and more. All these functions are integrated in a single lightweight test case without the need of connecting additional external modules.
