Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI 5A Fault Insertion Switch 5-Channel
40-196-101
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
product
Custom Orthogonal 20 Slot 15U
Fully custom system design is based on the orthogonal topology. It allows for massive switching bandwidth between front computing slots and rear switching slots to be used in Telecom and Datacom industries.
-
product
CompactPCI Serial 21 Slot Custom
21 slot fully custom backplane is based on CompactPCI® form-factor and features PCI-E star topology along with 12V server PSUs and dedicated chassis monitoring card for industrial control application.
-
product
NI TB-2640B Terminal Block for NI 2532B as 1-Wire 4x128 Matrix Topology Without Column Protection Resistors
782385-01
Screw Terminal, Ribbon, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2640B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2640B to the front panel I/O connectors … of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2640B also provides optional isolation resistors to protect the reed relays from capacitive loads.This 782385-01 card does NOT have 100 Ohm protection.
-
product
cPCI Serial Chassis 4 Slots
4U 32HP
As the established PICMG 2.0 CompactPCI has evolved, so has Hartmann Electronic’s product line. The 4U cPCI 4 slot solution is designed with quality and versatility in mind. This chassis comes complete with a 3U, 4 slot PCIe Gen3 backplane with full mesh topology, powered by a 180W ATX power supply.
-
product
NI TB-2643B Terminal Block for NI 2532B as 1-Wire Dual 4x64 Matrix or 2-Wire 4×64 Matrix topology With Column Protection Resistors
782385-08
The TB-2643B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x64 or 1-wire dual 4x64 matrix. You can directly connect the TB-2643B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2643B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
Downconverter
MADC-011021
Macom Technology Solutions Holdings Inc.
The MADC-011021 is a surface mount E-band receiver. The module operates from 71 - 86 GHz and is designed to be used in direct conversion or heterodyne applications. The RF input is a WR12 interface. The module provides 12 dB of conversion gain and a noise figure of 5 dB. The linear mixer topology allows for strong IIP3 performance (2 dBm) to be maintained up to the radio input levels recommended in the standards. The baseband is a quadrature balanced four line interface (I, I*, Q, Q*).
-
product
PLC Module Functional Tester
Functional test system for testing PLC peripheral modules. The DUTs are examined with the help of the system before repair and calibrated and finally tested after repair. With the help of product-specific personality modules, the internal cabling of the system can be adapted to various test object topology without the need for a large number of matrix channels.
-
product
3U CompactPCI Serial Blades
The PICMG CPCI-S.0 CompactPCI Serial standard, which evolved from the PICMG 2.0 specification, is the fastest, most versatile, most cost-effective open standard for CompactPCI (CPCI). The Serial standard is mechanically and electronically compatible with 3U and 6U euro-cards, defining an interface for high-speed switched fabrics with a star topology. Point-to-point connectors allow up to eight peripherals on one system slot without switches or bridges. Ethernet data transfer can be configured with full mesh topology, which allows up to 1000Base-T connections to all peripheral slots for redundant, safety-critical systems.
-
product
Open Source Real-time Network Topology & Protocols Analyzer
Skydive
Skydive is an open source real-time network topology and protocols analyzer. It aims to provide a comprehensive way of understanding what is happening in the network infrastructure. Skydive agents collect topology informations and flows and forward them to a central agent for further analysis. All the informations are stored in an Elasticsearch database. Skydive is SDN-agnostic but provides SDN drivers in order to enhance the topology and flows informations. Currently only the Neutron driver is provided but more drivers will come soon.
-
product
Firewall Analyzer
Instantly visualize your entire hybrid network security topology – in the cloud, on-premises, and everything in between. Understand the impact of network security policies on traffic, quickly troubleshoot connectivity issues, plan changes, and perform “what-if” traffic queries.
-
product
Microwave Generators And Systems
MKS offers compact industrial microwave generators and systems in 915MHz and 2450MHz that are adaptable to a wide range of applications including include Food and Beverage Packaging, Environmental and Advanced Industrial processes like coating, material growth, and automotive. With a robust, modular power system chassis design and advanced filament and electromagnetic management, MKS microwave generators are engineered to last. The microwave generators are equipped with switch mode topology for all power ranges and support a variety of fieldbus communication protocols.
-
product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix Topology Without Column Protection Resistors
782385-03
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
VPX Chassis 4U/42HP 5 Slots Desktop
This 5 slot Hartmann VPX 4U desktop system chassis provides a portable packaging solution for high-performance processors on a full mesh backplane topology. The 42HP wide desktop enclosure for vertical mounting of boards is outfitted with a 300W ATX power supply and a 1U fix bottom mounted fan tray.
-
product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix Topology Without Column Protection Resistors
782385-05
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
NI TB-2644B Terminal Block for NI 2532B as 1-Wire Dual 8x32 Matrix or 2-Wire 8×32 Matrix Topology Without Column Protection Resistors
782385-09
The TB-2644B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 8x32 or 1-wire dual 8x32 matrix. You can directly connect the TB-2644B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2644B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
AERINOS Sigfox IoT
Infinite Industrial Informatics Lt
Sigfox is a communication protocol that is used to read data from sensors through a fixed network of base stations. It works like a low cost “SMS” service. As an end-user, you only need to buy a subscription to connect to the data network operated by SIGFOX. Sigfox employs a proprietary Ultra Narrow Band (UNB) radio technology that enables communication using the Industrial, Scientific and Medical ISM radio band, which uses 868MHz in Europe and 902MHz in the US. It has the advantage of covering larger areas than other fixed local systems.The overall Sigfox network topology has been designed to provide a scalable, high-capacity network, with very low energy consumption, while maintaining a simple and easy to rollout star-based cell infrastructure. The density of the cells in the Sigfox network is based on an average range of about 30-50km in rural areas and in urban areas, where there are usually more obstructions and noise is greater, the range may be reduced to between 3 and 10km.According to the latest numbers, Sigfox has a nationwide live coverage in 6 countries and in 14 other countries it is deploying and rolling out ts network. By end 2018, the ambition is to cover 60 markets.
-
product
cPCI Serial 4U 84HP 9 Slots
As the established PICMG 2.0 CompactPCI has evolved, so has Hartmann Electronic’s product line. The 4U cPCI 9 slot solution is designed with quality and versatility in mind. This chassis comes complete with a 3U, 9 slot PCIe Gen3 backplane with single star topology, powered by two 300W cPCI Serial power supplies.
-
-
product
Text-Based Way to Connect & Disconnect Relays on ABex Modules
ABex Switching
The ABex Switching features a text-based way to connect and disconnect relays on ABex modules. Alias names for channels could be defined in a DUT specific topology file and then be used for text-based switching. These alias names are also shown in the Konrad System Manager allowing easy debugging of test sequences. The ABex Switching functionality could be either used out of NI Teststand with the provided test steps or via API from other programming languages.- Text-based switch routes- XML based topology for Alias mapping- Switch routes with support for Alias names- Seamless integration into Konrad System Manager
-
product
NI TB-2646B Terminal Block for NI 2532B as 1-Wire Quad 4x32 Matrix topology With Column Protection Resistors
782385-14
The TB-2646B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire dual 4x32 or 1-wire quad 4x32 matrix. You can directly connect the TB-2646B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2646B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
Network Management
PLANET Universal Network Management System is designed to monitor all kinds of deployed network devices, such as managed switches, media converters, routers, smart APs, VoIP phones, IP cameras, etc., compliant with the SNMP Protocol, ONVIF Protocol and PLANET Smart Discovery utility. It thus enables the administrator to centrally manage a network of up to 1024 nodes from a central office, greatly boosting network and power management efficiency. The NMS solution includes the software, hardware and Touch LCD controller series to attend to different applications. They all feature dashboard, topology and map viewing to make network management efficient and effective.
-
product
PXI 5A Fault Insertion Switch 10-Channel
40-196-001
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
product
Ultrafast Rectifiers
The ST rectifier diode designs deliver performance for applications with very different VF/Qrr trade-offs depending on targeted functions. The minimal power losses of the ST rectifiers range is totally adapted to mains rectification, bypass, boost, bootstrap, freewheel and HF rectification functions. Inside these generic functions, the topology evolution in e.g. resonance or multilevel is followed constantly by suited designs. Ultrafast rectifiers are belonging to the STPOWER family.
-
product
NI TB-2645B Terminal Block for NI 2532B as 1-Wire Dual 16x16 Matrix or 2-Wire 16×16 Matrix Topology Without Column Protection Resistors
782385-11
The TB-2645B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 16x16 or 1-wire dual 16x16 matrix. You can directly connect the TB-2645B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2645B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
Software
Osiris
Osiris gives a unique insight into your industrial network’s health and topology. This powerful software lets you remotely monitor your Industrial Ethernet and PROFIBUS installations from anywhere in the world.
-
product
Universal Switch
34980A
34980A Universal Switch Module 34937A, 34938A can be used to send signals or control other devices in the application. The 34937A is a versatile universal switch with 28 channels capable of switching up to 1A. In addition, there are four can switch up to 5A of the A-channel. The 34938A has 20 5A channels of type A topology. Each type A general-purpose switch can withstand up to 150W of power per channel, suitable for power switching.
-
product
Voltage Variable Attenuators
Analog Devices voltage variable attenuators (VVAs) ensure accurate control for a wide range of applications. Our absorptive VVAs are ideal for designs where an analog dc control signal controls RF signals levels over a 30 dB amplitude range, while our monolithic VVAs feature low insertion loss, high IP3, and wide dynamic range, as well as a balanced topology that delivers excellent return loss.
-
product
40V Multi-Output Isolated Topologies
Renesas' 40V multi-output isolated topology demonstration platforms use a single synchronous buck converter to realize multiple outputs (both inverting and non-inverting) as well as voltage step up/down function.
-
product
NI TB-2640B Terminal Block for NI 2532B as 1-Wire 4x128 Matrix Topology With Column Protection Resistors
782385-02
The TB-2640B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2640B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2640B also provides optional isolation resistors to protect the reed relays from capacitive loads.
