Filter Results By:
Products
Applications
Manufacturers
Traffic Generation
simulate communications over a network.
- InterWorking Labs, Inc.
product
Remote Monitor Management Information Base
SNMP RMON MIB
For every control table in the MIB, create and delete rows with various combinations of SNMP requests (all variables in a single request throughall variables in individual requests).Determine which row of this table is modeling the ethernet interface connected to the agent (requires that we are using ethernet). Check that this is for the same interface discovered in the "interfaces" test. Check counters.Build a history control row pointing to the interface connected to the agent. Check validity and traffic reported.Test agent's ability to generate an alarm on an RMON variable, then on threshold condition. Test for support of alarms on failing events, and in the event of target variable vanishing.Set up agent to track hosts on the ethernet interface connected to the agent. Check that entry was added for Rmon device's own ethernet address.Generate various top N reports (hostTopN test) and check validity.Start a matrix capture and check that the src-dst and dst-src tables are in sync.Check a channel and check for event generation (filter test).Create a channel and start a capture. Test locking and wrapWhenFull operation.
-
product
SAS (Serial Attached SCSI)
Serial Attached SCSI (SAS) is a data transfer technology designed to move data to and from storage devices such as disk drives, host bus adapters (HBA), and expanders. SAS is a serialized enhancement and replacement to parallel SCSI. Since SAS ratification in 2004, and it’s move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with it’s industry leading protocol analysis and traffic generation capabilities.
-
product
Multi-Service Transport Test Solution
MX Series
The VeEX MX product series offer a complete test solution for Metro Ethernet network installation and maintenance. Powerful features such as symmetrical and asymmetrical RFC2544 conformance testing, Multiple independent stream generation, Stacked VLAN (Q-in-Q) and MPLS tagging, and Dual Port Traffic Generation/Analysis are available at 10GBase-R, 1000Base-X and 10/100/1000Base-T test interfaces. Fiber Channel testing at 1Gbps and 2Gbps rates is supported on select models.
-
product
1GbE/10GbE Test Blade with Line-Rate L4-7 Application Performance
Xcellon-Ultra NP Load Module
Keysight Network Applications and Security
Ixia''s Xcellon™ load modules are the highest performing and most scalable application traffic generation solution available in the industry. The Xcellon-Ultra™ NP offers complete layer 2-7 packet generation, routing, and application testing functionality in a single load module.
-
product
New Generation Analyzer for IPTV Field Servic
NetProbe 2000 IPTV
New Generation Analyzer for IPTV Field Service The NetProbe 2000 IPTV is the newest, state-of-the-art handheld analyzer on the market for field testing of IPTV customer services. It can monitor up to 40mbps of IPTV traffic and emulate a Set-top box.
-
product
Protocol Test Platform
USB Explorer 350
The revolutionary Ellisys USB Explorer 350 (EX350) is a super-compact yet sophisticated and comprehensive protocol test and analysis system for USB 3.1 (Gen1 and Gen2), USB 2.0, and USB Power Delivery 3.0. Full support of USB Type-C (including CC and Vconn) is provided with an adapter and cables.With many innovative and exclusive features, the USB Explorer 350 meets the demands of today’s technology developers by providing unmatched coverage for protocol analysis, traffic generation, and compliance testing for emerging USB technologies.
-
product
NVMe Testing Software
IOL INTERACT™
IOL INTERACT™ software expedites and automates the testing of NVMe SSDs and NVMe-oF products. It is used to test products for inclusion on the NVMe Integrator's List. Members of the UNH-IOL NVMe Testing Services are entitled to a copy of INTERACT™ for in-house testing to ensure that their products will meet the Integrator's list requirements when submitted for testing. While most test requirements can be performed with the PC edition tool, a subset of tests specific to PCIe products are only available on the Teledyne-LeCroy tool, which require low level traffic generation capability.
-
product
Modular Test Platform
MPA®Multi-Protocol Analyzer
The MPA® Multi-Protocol Analyzer is an advanced packet optical transport traffic generation and analysis platform specifically designed for the demands of R&D, SVT, and manufacturing testing environments. The MPA provides simultaneous independent multi-port testing from 1G to 400G for Ethernet/IP, OTN & SDH/SONET and Fibre Channel.
-
product
Two Port SAS?SATA Analyzer
Sierra M122A
The Sierra M122A is Teledyne LeCroy’s two port SAS / SATA analyzer with special licensing to allow 6 Gb/s protocol capture. This multifunction platform is available with an integrated traffic generation option capable of host and device emulation. There is also a “Jammer” option for stress testing at the system and component level. This model of the Sierra M122A is configured for 6Gbps SAS & SATA protocol capture and can be field-upgraded to support 12Gb/s SAS testing.
-
product
Next Generation Network Testing
UX400
The VeEX UX400 is the smallest multi-service transport test solution to offer test capabilities ranging from DS1/E1 all the way up to 6x 100G traffic generation, supporting the latest 100G/40G optical pluggable form factors (CFP4, CFP2, CFP, QSFP28, QSFP+, no adapters required). Its modular architecture allows for up to six independent test modules and up to twelve concurrent tests or combinations of tests, including legacy PDH/DSn, SDH/SONET, OTN, Ethernet, Fibre Channel, CPRI/OBSAI, C/DWDM spectrum analysis and more. The platform's software architecture has been developed so that multiple users or scripts are able to access and operate different test modules at the same time, maximizing the use of resources. A battery backup option is available for the portable UX400 platform. Test modules can also operate in a standard 19" rack – the UX400R, when portability or battery operation is not needed.
-
product
1U Rackmount Network Appliance Platform With LGA1150 Socket Intel® Xeon® E3/Core™ Family Processor, Intel® C226 And Up To 24 LANs
NA570
NA570 1U rackmount Network Security Platform, supports the 4th generation Intel® Xeon® E3 / Core™ processor family, formerly codenamed "Haswell". NA570 offers greatly improved performance and reduced power consumption base on the new Intel architecture marked improvements in power efficiency and performance. The system supports up to 32GB DDR3 1600 non-ECC / ECC (only NA570) memory. NA570 support 4 pairs of LAN Bypass function. Bypass ports allow users to experience uninterrupted network traffic even if a single in-line appliance hangs or sudden shutdown. Expandable LAN Modules via the PCIe 3.0, support up to 24 GbE ports, or up to 4 ports at 10GbE, and a future upgrade to 40GbE, port density and optional networking ports to suit your demands.
-
product
Network Testing
UX Series
The VeEX UX series includes the robust UX400 and UX400R Universal Expert platforms. The UX400 is the most versatile portable multi-service transport test solution to offer a wide range of modules with test capabilities ranging from DS1/E1 all the way up to the latest 100GE and OTU4 network speeds, for a total of up to 600G traffic generation in a single compact modular chassis. Available in Portable and Rack-mount versions.
-
product
Interface
RCNIC-A2PAX
The RCNIC platform is a high performance, PCI module (PMC on carrier card) for the AFDX / ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
product
SDH Ethernet Testers
Wuhan Sunma Technology Co., Ltd.
The SunmaFiber SDH & Ethernet is easy to use, cost effective Ethernet testing solution for basic physical layer cable testing, layer 2 and layer 3 traffic generation, and full RFC 2544 testing. The rugged, battery operated, application specific test tool enables field technicians to turn-up Ethernet and IP services by running an RFC 2544 test or following a set of methods and procedures. The product has been designed for front-line technicians who do not have experience dealing with emerging Metro Ethernet technologies and need a simple to use solution for Ethernet and IP testing.
-
product
Ethernet Tester
GAOTek Gigabit
GAOTek Gigabit Ethernet Tester is a handheld tester for installation, commissioning and maintenance of 10M/100M/1000M ethernet networks. By combining network performance test & monitoring, data packet sniffing, traffic generation, cable test and BER test in one unit. It is widely used in testing BER of layer 1, layer 2, layer 3, and full-featured RFC-2544 and Y.1564 testing. It can help the front-line field technicians analyze the network quality and locate the fault rapidly.
-
product
10G Ethernet/IP Network Infrastructure Testing Application
GENEM-X
GENEM-X is a high-capacity network infrastructure testing software application for network equipment manufacturers, data centers, service provider telco cloud and 5G backhaul. It runs on Siama’s carrier-class PROVA-X hardware appliance. GENEM-X allows you to verify, monitor and troubleshoot Ethernet/IP network equipment and data center applications to ensure network services can accommodate the demands of your customers. Ideal for QA test, Service Providers migrating to a DevOps model can use GENEM to validate service turn-up and modifications in the production network. GENEM is equally at home in a lab environment. It bundles wire-rate traffic generation and analysis capabilities with a network emulator and packet capture/replay function in a single software license.
-
product
1U Rackmount Network Appliance Platform
NA861
The NA861 offers high processing performance through the LGA3647 socket 2nd Generation Intel® Xeon® Scalable processor (codename: Cascade Lake) and supports the Intel® C621 chipset. The robust and highly reliable network appliance platform comes with two Gigabit Ethernet ports and four expandable LAN modules supporting 1GbE/10GbE/Fiber/Copper/Bypass with a maximum of thirty-four LAN ports. The NA861 is the perfect network hardware solution for enhancing digital security & surveillance, network traffic management and virtualized network security.
-
product
TestPort Line Of Hand-Held Ethernet Test Equipment
The TestPort line of handheld Ethernet protocol test tools represents the state-of-the-art test equipment for telecom backhaul networks. It’s protocol support includes Gigabit Ethernet (GbE), Sychronous Ethernet (SyncE), and E1. Testing applications include protocols analysis, traffic generation, and impairment testing.
-
product
Metro Expert
MX Series
The VeEX® MX product series offer a complete test solution for Metro Ethernet network installation and maintenance. Powerful features such as symmetrical and asymmetrical RFC2544 conformance testing, Multiple independent stream generation, Stacked VLAN (Q-in-Q) and MPLS tagging, and Dual Port Traffic Generation/ Analysis are available at 10GBase-R, 1000Base-X and 10/100/1000Base-T test interfaces. Fiber Channel testing at 1Gbps and 2Gbps rates is supported on select models.
-
product
Protocol Exerciser
Summit Z416
The Summit Z416 is a PCIe 4.0 protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z416 can emulate PCI Express 4.0 root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
product
USB Protocol Verification System
Voyager M310e
The Voyager M310e is Teledyne LeCroy's flagship USB protocol verification system designed for USB 2.0, USB 3.2, Type-C, and USB Power Delivery. Offering the industry's highest fidelity probe design, flexible traffic generation, and a range of turnkey Compliance packages, the Voyager M310e is the most complete platform for cradle-to-grave USB design verification.
-
product
Software Testing Tool
LanTraffic V2
LanTraffic V2 is a software testing tool allowing UDP and TCP traffic generation on an IP network.
-
product
PCI Express 5.0 and Compute Express Link Protocol Exerciser
Summit Z516
The Summit Z516 is a PCIe 5.0 and CXL protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z516 can emulate PCI Express 5.0 and CXL root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
product
Multi-Functional Ethernet Test Solution
PacketExpert™
PacketExpert™ 10GX is a comprehensive Ethernet/IP test solution supporting industry standard functionalities including wirespeed bit error rate testing (BERT), RFC 2544 / Y.1564 / RFC 6349 tests, packet capture, event-driven triggers and actions, traffic playback, impairment generation, stacked VLAN/MPLS tests, and many others.
-
product
SATA (Serial ATA)
Serial ATA (SATA) is a data transfer technology designed to move data to and from storage devices such as disk drives, ATAPI drives, host bus adapters (HBA), and port multipliers. SATA is a serialized enhancement and replacement to parallel IDE. Since SATA ratification in 2003 and its move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with its industry leading protocol analysis and traffic generation capabilities.
-
product
Ethernet and Fibre Channel Test Platform
SierraNet M648
The SierraNet M648 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M648 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M648 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
product
GAOTek Handheld Gigabit Ethernet Tester
A0060001tek
GAOTek Handheld Gigabit Ethernet tester is designed for installation and maintenance of 10 M/100 M/1000 M Ethernet networks. It combines the functions of network testing, data packet capture, traffic generation, cable testing and BER testing into one unit. It also integrates full RFC-2544 and Y.1564 tests. Featuring an ergonomic design and 5.0 inch LCD color touch screen, this Ethernet tester helps the front-line field workers to analyze the network quality and locate faults rapidly. Test results can be shown graphically and numerically.
-
product
Ethernet and Fibre Channel Test Platform
SierraNet M1288
The SierraNet M1288 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M1288 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M1288 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
product
Time-Triggered Ethernet / ARINC 664 Part 7 (AFDX®) / IEEE 802.3 Ethernet Deterministic Communications
TE2
Module TE2 is one of NAI's latest generation of advanced function Configurable Open Systems Architecture™ (COSA®) compatible modules. The TE2 is a certifiable, single-port, tri-redundant, deterministic Ethernet communications interface module that supports TTTech’s certifiable TTEthernet® End System product consisting of three traffic classes: SAE AS6802 (Time-Triggered Ethernet), ARINC 664 Part 7 (Avionics Full-Duplex Switched Ethernet (AFDX®), and/or IEEE 802.3 best-effort protocol. By supporting all three traffic classes, NAI's TE2 is the ideal solution for current users of IEEE 802.3 Ethernet, who plan to upgrade to Deterministic Ethernet (ARINC 664 Part 7 (AFDX®) or Time-Triggered Ethernet SAE AS6802) protocols in the future at any time without changing hardware.
-
product
PROVA-X
10G Ethernet/IP Test Appliance. The PROVA-X is a packet-based test appliance for communications service providers, network equipment manufacturers and data centers. This appliance can be used to test and analyze the behaviour and performance of an Ethernet/IP network or device. Synthetic traffic generation, packet capture, emulation, impairment and performance assessment tool.
