Filter Results By:
Products
Applications
Manufacturers
-
product
End of Line Test System for Automotive Seats
AS519
AS519 is specifically designed to perform ECU’s EOL tests in the automotive industry. It integrates a programmable power supply up to 20V 20A with high reading resolution. Interaction with the DUT is established through CAN bus by an interphase adapter in a USB port of the test managing computer.
-
product
USB Hub
The USB Hub's output ports can be connected or disconnected programmatically to simulate the mechanical connection of a USB device to the module. Additionally, each port has the ability to connect and disconnect the power and data paths separately, enabling the simulation of various connection faults. Take a look at our article, "Bringing USB to the PXI Test Environment" .
-
product
USB Test Hardware
Test stations with USB hardwareHardware control of adapters with USB-I / OFlash and microprocessor programmer
-
product
MCCI USB Test Services
MCCI's Test Lab offers quick, cost-effective USB-IF Logo Compliance Testing for low-speed, full-speed and high-speed devices, and for low- and full-speed systems. As a certified logo-test facility, we can save you time, and give you expert advice.
-
product
USB A TX Test Fixture
AUT20135
This newly designed AUT20135 brings enhanced user-experience with the following features:
-
product
USB PD Test System
6050
Single Output USB PD USB PD basic version：the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
product
USB Controlled Audio Test Interface
AudioConnect
AudioConnect is a 2-in, 2-out audio interface specifically designed for audio test and measurement. It offers digital and analog audio in and out, a a 44.1kHz/48kHz sampling rate, USB control, and a power indicator; all other typical soundcard controls that are not used for audio test applications have been eliminated. This makes operation and calibration simple with no room for error.
-
product
USB Power Delivery Test Equipment
The Packet-Master USB-PDA is a USB PD Analyser, for FSK and Baseband variants of Power Delivery.
-
product
Multi-Protocol Test & Simulation Adapter for USB or Ethernet
EXC-UNET2/xx
The EXC-UNET2/xx is a multi-protocol test and simulation adapter for USB or Ethernet equipped computers. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of a number of communications protocols, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
product
ARINC 429 Test And Simulation USB Module
USB-429
*4, 8 or 16 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
USB 3.2 Receiver Compliance Test Software
N5991U32A
Maximize the usage of your test instruments with a fast and reliable application to automate system calibration and USB 3.2 receiver compliance tests.
-
product
USB Controlled Loudspeaker & Microphone Test Interface
AmpConnect™ ISC
AmpConnect ISC is an all-in-one audio interface that simplifies your test setup and operation. It is a single, rugged, rack-mountable piece of hardware containing a high-accuracy audio interface, impedance box, amplifier, headphone amplifier, 2 microphone power supplies and digital I/O. It replaces multiple hardware devices, connecting to your computer via a single USB cable, and it is fully controlled by SoundCheck. This simplifies setup and calibration, eliminates cabling and reduces connectivity errors, as well as reducing overall system cost.
-
product
USB Type-C Interconnects Compliance Test Software
S94USBCB
Use the S94USBCB software to test, debug and characterize your USB Type-C cable and connector designs. The PathWave TAP based test sequencer automates the network analyzer (VNA) for each test and generates a comprehensive HTML report. When run with L8990M switch matrix, it enables 20-ports fully automated test without port re-connection.
-
product
USB
The introduction of USB 3.2 and USB4 along with the Type-C connector ushers in a new era of unprecedented performance for consumer electronics that can now utilize this universal interface for power, data and display. Positioned as the primary high-performance interconnect for the next decade, developers are ramping up their USB3.2 / USB4 expertise. From engineering validation to compliance test, trust the experts at Teledyne LeCroy to help ensure product compatibility for next generation USB systems.
-
product
ARINC 429 USB & LAN Test & Simulation Module
UXI-429
Avionics Interface Technologies
8 Channel (4Tx/4Rx) & 16 Channel (8 Tx/8 Rx) models available - Programmable Tx channel output amplitude - Programmable high/low speed operation - Concurrent operation of all Tx/Rx channels at high speed rates - Full error injection & detection - Rate-oriented label transmission - Label selective trigger for capture/filtering - Real-time recording & post analysis of multiple channels - Physical Bus Replay - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs)
-
product
MIL-STD-1553 A / B Test And Simulation USB Module
USB-1553
*Dual redundant*1 or 2 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*More programmable triggers and acquisition*10 programmable I / O*Onboard IRIG-B timecode encoder / decoder*Supports stand-alone operation via USB connection, without external power supply*On-board battery for runtime without power supply
-
product
MIL-STD-1553 USB & LAN Test & Simulation Module
UXI-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsConcurrent BC, 31 RTs, and BM operations - Physical Bus ReplayFull error injection/detection capabilities - Programmable trigger and capture - Programmable Bus Coupling and Output Voltage Levels - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs) - Operates from a single USB or Ethernet LAN connection - Supports SAE AS4112/4114 protocol testing requirements- Flight Simulyzer™ GUI Analyzer software
-
product
USB 2.0 SmartCable For MIL-STD-1553 Test And Simulation
ASC1553
The ASC1553 (AIM SmartCable) USB module offers full function test, simulation, monitoring and recording for MIL-STD-1553B applications implemented in an ultra compact form factor.
-
product
USB Controlled High Precision Audio Test Interface
AudioConnect 4×4
AudioConnect 4×4 is a high accuracy 4-in, 4-out audio interface specifically audio test and measurement. It offers digital and analog audio in and out at any user-specified sampling rate up to 200kHz, and a high signal to noise ratio and wide frequency response, making it suitable for the most demanding measurement applications. Controls are simple – a single USB connection and a power indicator – all other typical soundcard controls that are not used for audio test applications have been eliminated to make operation and calibration simple with no room for error. AudioConnect 4×4 is supplied fully calibrated.
-
product
USB Oscilloscope
Handyscope HS6 DIFF
This powerful USB 3.0 super speed oscilloscope combines fast sampling up to 1 GS/s with high resolutions of 12, 14 and 16 bit and a large memory of 64 MSamples on all four channels. The oscilloscope supports continuous streaming measurements up to 200 MS/s and can be synchronized with other oscilloscopes using the CMI interface to form a multi channel combined instrument with synchronized timebase. The CMI interface is available by default on the Handyscope HS6 DIFF. Optionally, the Handyscope HS6 DIFF can be delivered with SureConnect connection test and resistance measurement on each channel. Also, the Handyscope HS6 DIFF can be delivered with SafeGround option. With SafeGround you can switch the differential inputs of the Handyscope HS6 DIFF into single ended inputs with ground protection. It allows to make measurements using standard attenuating probes and protects the scope when a short circuit to ground is created.
-
product
USB⇔RS-232C
SI-55USB
SI-55USB is an USB converter, which converts USB of PC into RS-232C serial port of signal-isolated type. Virtual COM port driver ease the usage of test software and shorten the time of installing the new system. Features of this product are max 1Mbps baud rate and 3000V high-voltage resistant isolation by photo coupler and isolated power unit.
-
product
Upgrade - Accessory Kit For 34460A - Test Leads, USB Cable
3446ACCU
3446ACCU provides the accessory kit for the 34460A, including the test leads and USB cable.
-
product
USB-C® – USB 2.0 Receptacle HS SQ Test
AUT17037
This product is designed for USB-C USB2.0 Plug Host/Device Electrical Test.
-
product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
A USB Type-C test interface board for CableEye® cable and harness testing systems. Consisting of a daughter board, populated with two USB-C female connectors, it allows users to continuity-check USB Type-C terminated cables using the CableEye tester while seeing the connectors-under-test rendered graphically. The CB26U fits all CableEye models.
Configuration
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test. Sold as a set of two boards, each CB26U accepts two USB Type-C connectors. In addition to the latest CableEye software, it requires the CB26 small-frame motherboard (Item 756) for operation, and plugs into one of two available slots – two USB-C-connectors can be tested simultaneously. The CB26 (with CB26U) attaches to the tester like a regular connector board.
Contact sales@camiresearch.com or +1 (978) 266-2655 for a quote. -
product
USB-C® – USB 2.0 Plug HS SQ Test Fixture
AUT17094
This product is designed for USB-C USB2.0 Receptacle Host Electrical Test.
-
product
JTAG USB Controller
NetUSB-1149.1/E
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
product
USB Compliance Testers
The Packet-Master USB-PET is a Protocol and Electrical Tester capable of performing thesuite of tests defined in the USB-IF specifications for OTG 2.0, and Battery Charging. The PET tester hardware was designed in co-operation with the USB-IF USB On-The-Go Work Group, and the Battery Charging Work Group.
-
product
USB Databus Analysers
SOAR Family
With Desktop PC PCI slots rapidly following ISA into the history of computing, we believe that our USB based solutions are an excellent way of protecting your test gear investment from obsolescence.
-
product
USB JTAG controller
The small, lightweight design means the XJLink2 can easily be moved to the Unit Under Test (UUT). Advanced features, like their programmable JTAG signal pin position, switchable power supply and auto signal skew, make it easy to connect to a wide range of circuit boards. Simple to install and use due to the USB plug-and-play ability.
-
product
USB SOCKET TESTER
MDPPTSTUSB
*Provides the user with a simple way to test a USB socket on a vehicle*Mini probe will light up when 4.4V - 5.25V is detected
