Filter Results By:
Products
Applications
Manufacturers
-
-
product
Wafer Level Test
Double sided wafer inspection system is an automatic inspection system for afterdicing wafer chip. It can do double side inspection simultaneously. The appearance defects of wafer chip are clearly conspicuous by using advanced illumination technology. Illumination and camera acquisition mode can be adjusted for various wafer process, like vertical chip or flip chip.
-
product
Production Wafer Level Burn-in
TV19 VersaTile™ probe cards are designed with Celadon’s patented ceramic technology for superior electrical performance, yet is highly modular due to it’s 28mm x 28mm chassis. Micro-adjustments can be made in seconds with an allen wrench and a microscope. Easily align VersaTile cards for different wafer layouts using a 4.5” compatible 1×3 , 200mm, or 300mm VersAdjust plate.
-
product
System to Handle Wafer Levels
AMI AW Series
Operator-Free Wafer Inspection, Analysis and Sorting The AW Series are advanced high-capacity, high throughput automated wafer C-SAM® instruments specialized to deliver maximum sensitivity for the evaluation of wafer and device level applications.
-
product
Wafer Level Test Handler
Kronos
Wafer level test handler for 6/9DOF sensors with real stimulus. Very high UPH capacity and the lowest cost of test (COT). KRONOS is one of the only wafer level test solutions for motion sensors with real stimulus.
-
product
Inspects MEMS and Wafer Level Devices
NorCom 2020-WL
The NorCom 2020-WL is specifically designed for wafer-level inspection and leak tests up to 1000 devices per cycle. The system can inspect up to an 8” wafer on or off a saw frame. It is designed to test MEMS and other wafer level devices that have a cavity.
-
product
MultiSite Test sockets and Wafer Level
multi-site sockets include anything from strip test sockets to test sockets for wafer test to multi-position, singulated devices. The advantages of these sockets can be enormous as test time can be decreased by a factor of ten over conventional one up testing. In most cases, the throughput is only limited by tester capabilities and/or handling capacity.
-
product
Wafer Level Multi-Die Test System
ITC55WLMD
The ITC55WLMD series of test systems has been developed by ITC to be stand-alone UIL test systems configured specifically to test on wafer. The systems include an ITC55series UIL tester and inductor box, a current limiter module and a system controller
-
product
Wafer Test
Silicon Turnkey Solution, Inc.
Most foundries provide wafers already probed to a set of DC parameters at room temperature to ensure they meet a basic subset of the package-part specification. Beyond this basic set of tests, more rigorous testing is often needed to meet specifications requiring die to be 100 percent probed, identify and segregate devices with higher performance levels and guarantee that parts will perform to a certain specification level.
-
product
Wafer Test
Automatic KLA wafer probers with tray-to-tray-wafer-handling are operated 24h a day and 7 days a week. Data retention bake/tests are done at wafer level
-
product
Wafer Bonding Systems
ith over 15 years experience in designing and manufacturing precision wafer bonding equipment, EVG wafer bonding systems are well recognized in setting industry standards for the MEMS production industry. Besides supporting wafer level and advanced packaging, 3D interconnects and MEMS fabrication, the EVG500 series wafer bonding systems can be configured for R&D, pilot-line or volume production. They accommodate the most demanding applications by bonding under high vacuum, precisely controlled fine vacuum, temperature or high pressure conditions. Multiple bonding methods including anodic, thermo compression, glass-frit, epoxy, UV and fusion bonding are covered. Based on a unique modular bond chamber design the EVG500 series allow for an easy technology transfer from R&D to high volume production.
-
product
Wafer Inspection Products
Sonix provides manual and automated wafer inspection and metrology systems for wafers ranging from 100mm to 300mm, with extensive analysis capabilities at both the wafer and device level. These industry-leading automated wafer inspection systems are used by the world’s top manufacturers to ensure quality from development through production.
-
product
WDXRF Wafer Analyzer
2830 ZT
The 2830 ZT wavelength dispersive X-ray fluorescence (WDXRF) wafer analyzer offers the ultimate capability for measuring film thickness and composition. Designed specifically for the semiconductor and data storage industry, the 2830 ZT Wafer Analyzer enables the determination of layer composition, thickness, dopant levels and surface uniformity for a wide range of wafers up to 300 mm.
-
product
Automated Wafer Handler up to 450mm
GPR-GB7S
The GB7S Robot System employs Genmark’s breakthrough and patented GPR™ Technology to achieve the highest level of performance currently available in an automated wafer handler which is capable of handling up to 450mm diameter wafers. The patented GPR technology enables the servo-controlled robot to interface compliantly and intelligently with misaligned cassettes, FOUPS and process modules, as well as provide software-controlled end-effector deflection compensation during transport of heavier payloads. The unique and patented YAW technology feature of the GPR-GB7S Robot System enables it to access in-line process modules, FOUPS and cassettes from a fixed centralized location, and eliminates the need for radial placement of process and other stations around the robot. The GB7 Robot System can have various arm configurations to accommodate a wide range of SMIF/cassettes front-end layouts.
-
product
Bond Tester for Wafers 2 - 12 inch
Sigma W12
Bondtester for wafers or at wafer level 2” – 12” (up to 300 mm)Precise testing and Cold Bump Pull (CBP) testingLarge X/Y stages X: 600mm, Y: 370 mmForce range from 1gf – 10 kgfBump pitch down to 20 µm
-
product
LED Type Wafer Alignment Sensor Controller
HD-T1
Panasonic Industrial Devices Sales Company of America
The HD-T1 Series is a new Wafer Alignment Sensor that uses a safe red LED light beam, with a resolution of 30µm, to achieve the same high level performance as Laser Sensors. The HD-T1 Sensor is best suited to detect wafer eccentricity, notches and orientation flats. Using linear image Sensor methodology and high-speed sampling technology, a wide variety of objects can now be stably measured with great precision at ultra-high speeds. This CCD style Sensor is developed for use in almost all fields of industry, e.g. tire manufacturing or Semiconductor production (Wafer Printed Circuit Boards).
-
product
Single- and Dual-Yaw Axis Wafer Transport Robot
GPR-GB7SY
The GPR-GB7SY Yaw-Axis (single and dual yaw) robot features Genmark’s technologically advanced mechanisms including patented GPR and YAW technologies to achieve the highest level of performance currently available in an automated material handler capable of transporting up to 450mm wafer payloads with utmost reliability and precision.
-
product
120 A High Voltage 50 Ω Pulse Generator
TLP-12010C
High Power Pulse Instruments GmbH
- High pulse output current up to 120 A (short circuit)- Ultra-fast 50 Ω high voltage pulse output with typical rise time 100 ps (0 A to 40 A) and 300 ps in high-current mode (0 A to 120 A)- Wafer, package and system level TLP, VF-TLP and HMM testing- Up to 180 kW peak output power into 50 Ω load- Built-in HMM pulse up to ±32 kV in 50 Ω-configuration- High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)- 6 USB programmable pulse rise times: 100 ps to 50 ns (custom selectable)- 8 (optional 9) programmable pulse widths: 0.5 ns (optional), 1 ns to 100 ns (0 A to 40 A), 1 built-in pulse width: 100 ns (>40 A)- The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0 A to 40 A)- Optional external pulse width extensions from 5 ns to 500 ns (>40 A to 120 A)using the external pulse width extender TLP-12012A6- Built-in pulse reflection suppression- Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses- Efficient sofware for system control and waveform data management- The sofware can control automatic probers for fast measurements of complete wafers- Combines TLP-12010A and TLP-4010C into one system- Can be operated together with TLP-12012A6 and TLP-3011C pulse width extenders- Integrated interlock safety shut-down- Industrial isolated and EMI/ESD protected USB control interface
-
product
300 Mm Semiconductor Processes
With the Center Nanoelectronic Technologies (CNT), the Fraunhofer IPMS conducts applied research on 300 mm wafers for microchip producers, suppliers, equipment manufacturers and R&D partners. In the field of FEoL and BEoL we offer the following technology developments and services at Ultra Large Scale Integration level (ULSI):
-
product
±6 kV ANSI/ESDA/JEDEC HBM Test System
HBM-TS10-A
High Power Pulse Instruments GmbH
*±6 kV Human-Body-Model (HBM) tester according ANSI/ESDA/JEDEC JS-001 standard with C = 100 pF, R = 1.5 kΩ discharge network*Wafer, package and system level HBM testing*True HBM: the classical discharge network of the HBM-S1-A according the standard ensures compliant waveforms for all load conditions*No trailing pulses*Integrated 10 kΩ charge removal resistor*Integrated DUT HBM current sensor for real time transient current monitoring with 1V/A output sensitivity into 50 Ω digital oscilloscope input*Integrated DUT HBM voltage sensor for real time transient voltage monitoring with 1/200V/V output sensitivity into 50 Ω digital oscilloscope input*Integrated overvoltage protection of the DUT voltage sensor, DUTcurrentsensor and DC test interface for efficient overload protection of the digital oscilloscope and SMU during high voltage HBM testing*Integrated DC test DUT switch with automatic switch control*Integrated 50 Ω precision hardware trigger output for high speed digital oscilloscopes*Fast HBM measurements, typically 0.5s per pulse including one-point DC measurement between pulses*Eficient sofware for system control and waveform data management (fully compatible with TLP measurement data)*The sofware can control automatic probers for fast measurements of complete wafers*Compact size 145 mm x 82.5 mm x 44 mm of the integrated HBM pulse generator probehead*System controller size 483 mm x 487 mm x 133 mm*High performance and high quality components*Optionally available hardware upgrades to all HPPI fully integrated HBM/HMM/TLP/VF-TLP test systems TLP-3010C, 4010C, 8010A, and 8010C
-
product
AMIDA 5000 Tester
AMIDA 5000 is a high-end performance test system, combining analog, mixed-signal and logic with the latest test solutions. High pin count - as many as 512 smart multi-function pinframes and 128 sites. Ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. This system has a higher number of parallel tests and a higher level of capability. This series of test systems provides a powerful test combination with high-speed hardware and software integration. The 5000 series test system is the best analog, mixed signal, digital IC, PA test system for engineering verification and mass production. It can be easily connected to all well-known wafer probing machines and sorters, and also supports parallel test functions. The 5000 series meets customers' needs for high-precision, high-resolution, high-reliability, user-friendly, and low-cost testing and measurement of test systems.
-
product
Custom Assembly, Packaging and Qualification
DPACI specializes in providing Turn-Key Solutions. We offer comprehensive manufacturing, assembly, qualification, testing, and certification of high reliability EEE components. We have a dedicated, self-contained Class 10,000 clean room with Class 100 laminar flows certified to QML Q (Military) and V (Space) levels to perform all assembly operations from wafer processing to final hermetic package seal
-
product
Device Parameter Analysis
bsw TestSystems & Consulting AG
The complexity of DC Parametric Characterisations has significantly increased with the level of miniaturisation in the semiconductor industry. The demand is not only on the precision of the measurements. New measurement methods have emerged to gain insight into phenomena previously unknown or only of marginal relevance. One example is "Pulsed IV" which is now widely in use. The modular concept of the Keysight B1500A allows users to tailor their instrument exactly to their needs. Flexible upgrades ensure the investment for many years. Together with bsw AG you will get an optimum solution for your application. Our experts provide not only support for the instrument itself but have also working knowledge of all the solutions surrounding it. This includes Cabeling and Adapters, Fixturing for packaged Parts and of course Wafer Probing. We help customers from replacements of broken or worn-out parts to planning and deployment of turn-key-systems.
-
product
Equipment Front End Module (EFEM) Class 1 Minienvironment System
MiniMax™
Genmark’s MiniMax™ Equipment Front End Module (EFEM) is a class 1 minienvironment system designed to maximize productivity of semiconductor processing equipment tools that require the highest level of automation.The MiniMax™ can be customized to meet the automation requirements of any semiconductor manufacturing tool application and specified with one of the Genmark’s sophisticated and precise wafer and reticle handling robots, including the full line of patented GPR single or dual arm robots, GREX robot series, single and dual wafer aligners, FOUP/FOSB openers, reticle libraries, as well as any other customer specified equipment.
-
product
High Power Devices
SemiProbe configures our PS4L Adaptive Architecture into the Voltarus (TM) family of probe stations to fulfill the unique requirements of testing high power devices at wafer level prior to packaging. Voltarus probe stations are available in manual, semiautomatic, and fully automatic configurations that can test and characterize power devices up to 10 KV or 200 Amps (pulsed).
-
product
High Voltage 50 Ω Pulse Generator
TLP-12010A
High Power Pulse Instruments GmbH
- High pulse output current up to ±120 A (short circuit)- Ultra-fast 50 Ω high voltage pulse output with typical 300 ps rise time- Wafer, package and system level TLP and HMM testing- 180 kW peak output power into 50 Ω load- Built-in HMM pulse up to ±32 kV in 50 Ω-configuration- High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)- 6 digital programmable pulse rise times out of: 300 ps to 50 ns (optional)- 1 built-in pulse width: 100 ns- Optional external pulse width extensions from 5 ns to 500 ns using the external pulse width extender TLP-12012A6- Built-in pulse reflection suppression- Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses- Efficient software for system control and waveform data management- The software can control automatic probers for fast measurements of complete wafers- Integrated interlock safety shut-down- Industrial isolated and EMI/ESD protected USB control interface
-
product
High Voltage 50 Ω Pulse Generator
TLP-8010C
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Combines TLP-8010A and TLP-4010C into one system*Can be operated together with TLP-8012A5 and TLP-3011C pulse width extenders*Ultra fast 50 Ω high voltage pulse output with typical rise time 100 ps (0-40 A) and 300 ps (> 40 A)*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω configuration*High pulse output current up to ±80 A (short circuit) with minimum 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns (0-40 A), 1 built-in pulse width: 100 ns (> 40 A)*The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0-40 A)*Optional external pulse width extensions from 5 ns to 500 ns (> 40…80 A) using the external pulse width extender TLP-8012A5*Built-in pulse reflection suppression*Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components
-
product
High Voltage 50 Ω Pulse Generator
TLP-4010C
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
product
High Voltage 50 Ω Pulse Generator
TLP-8010A
High Power Pulse Instruments GmbH
*Wafer and package level TLP/HMM testing*Fast 50 Ω high voltage pulse output with typical 300 ps rise time*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω-configuration*High pulse output current up to ±80 A (short circuit) with 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 300 ps to 50 ns*1 built-in pulse width: 100 ns*Optional external pulse width extensions 5/10/50/100/200/500 ns using an external pulse width extender TLP-8012A5*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components
-
product
High Voltage 50 Ω Pulse Generator
TLP-3010C
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±8 kV*High pulse output current up to ±30 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
